Difficulty

Moderate

Steps

6

Time Required

                          1 - 2 hours

Sections

2

  • Back Cover Assembly
  • 2 steps
  • Flash Assembly
  • 4 steps

Flags

3

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackSamsung WB2100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover Assembly
  • Remove the 7 screws on the outside of the camera
  • Two 5 mm PH000 screws on the right side of the camera body
  • Four 3mm PH000 screws on the bottom and the left side of the camera body.
  • Use the plastic spundger to push the back casing out. Start from the right side and work your way clockwise around the case.
  • The HDMI / AV tab might fall out. this is supposed to happen as it is not screwed into place in the back casing.

Remove the 7 screws on the outside of the camera

Two 5 mm PH000 screws on the right side of the camera body

Four 3mm PH000 screws on the bottom and the left side of the camera body.

Use the plastic spundger to push the back casing out. Start from the right side and work your way clockwise around the case.

The HDMI / AV tab might fall out. this is supposed to happen as it is not screwed into place in the back casing.

1024

Step 2

  • Disconnect the set of wires from the back casing to the motherboard. Do this by using the plastic spundger to flip the black tab up and the wires will pull out.
  • Unscrew the four 3 mm and two silver 1 mm PH000 screw from the green logic board

Disconnect the set of wires from the back casing to the motherboard. Do this by using the plastic spundger to flip the black tab up and the wires will pull out.

Unscrew the four 3 mm and two silver 1 mm PH000 screw from the green logic board

Step 3

              Flash Assembly
  • Unscrew the two 3 mm screws from the top cover with the PH000 driver.
  • Along with the one 2 mm screw, also a PH000 screw.

Unscrew the two 3 mm screws from the top cover with the PH000 driver.

Along with the one 2 mm screw, also a PH000 screw.

Step 4

  • Use the spudger and pry the top cover off starting on the left side and working your way down.

Use the spudger and pry the top cover off starting on the left side and working your way down.

Step 5

  • After the top is disconnected, fold it back so the two PH000 flash screws are accessible and remove the cover.

After the top is disconnected, fold it back so the two PH000 flash screws are accessible and remove the cover.

Step 6

  • Remove the flash bulb from the red housing and clear cover. Do this by pushing back the flash bulb back out of the red housing.
  • When reassembling make sure the tab on the flash cover faces up.
  • Desolder the wires from the circuit board. Learn more about soldering here.

Remove the flash bulb from the red housing and clear cover. Do this by pushing back the flash bulb back out of the red housing.

When reassembling make sure the tab on the flash cover faces up.

Desolder the wires from the circuit board. Learn more about soldering here.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    McGregor Coyne

Member since: 01/20/2016

248 Reputation

                                      1 Guide authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team 15-3, Remmell Spring 2016                        

                                                  Member of USF Tampa, Team 15-3, Remmell Spring 2016 



                    USFT-REMMELL-S16S15G3                     


                                            4 Members                     


                                            6 Guides authored

Alain Chiesa - Oct 11, 2019

Reply

Hola, mi camara wb2100 se queda colgada y los comandos responden pasados varios segundos y al iniciar arranca con valores por defecto, es decir que no graba las configuraciones luego que se apaga, es muy molesto usarla de esta forma y quisiera saber si hay forma de resetearla para ver si se soluciona el problema. Alguien tiene idea de como resetear esta cámara? se agradece vuestra ayuda.