Difficulty

Moderate

Steps

10

Time Required

Suggest a time??

Sections

2

  • Rear Case
  • 4 steps
  • Screen
  • 6 steps

Flags

0

  • BackSamsung WB350F

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Rear Case
  • Remove the wristlet strap.
  • If you have difficulties use your plastic spudger. If you don’t have a plastic spudger, you can also use a pen/pencil.

Remove the wristlet strap.

If you have difficulties use your plastic spudger. If you don’t have a plastic spudger, you can also use a pen/pencil.

1024

Step 2

  • Remove five 3.2 mm screws with a Phillips #000 Screwdriver.
  • There is one silver screw on the bottom and two black screws on each side.
  • Keep the screws together for an easier re-assembly later.

Remove five 3.2 mm screws with a Phillips #000 Screwdriver.

There is one silver screw on the bottom and two black screws on each side.

Keep the screws together for an easier re-assembly later.

Step 3

  • Open the case of the camera using your plastic opening tool.
  • Start on each end, working the tool into the opening and popping the casing up. Then work your way down the longer sides (top and bottom).
  • If you don’t have plastic opening tools, any flat plastic object, like a used gift card, can be used as an improvised alternative.

Open the case of the camera using your plastic opening tool.

Start on each end, working the tool into the opening and popping the casing up. Then work your way down the longer sides (top and bottom).

If you don’t have plastic opening tools, any flat plastic object, like a used gift card, can be used as an improvised alternative.

Step 4

  • Remove the plastic casing, exposing the inner workings of the camera.

Remove the plastic casing, exposing the inner workings of the camera.

Step 5

              Screen
  • Using your Phillips #000 Screwdriver, remove one 3.2 mm screw above the menu buttons panel.
  • Next, remove the two 3.2 mm Phillips #000 screws to the left of the menu buttons panel.

Using your Phillips #000 Screwdriver, remove one 3.2 mm screw above the menu buttons panel.

Next, remove the two 3.2 mm Phillips #000 screws to the left of the menu buttons panel.

Step 6

  • Move the menu button panel to the right as well as the screen.
  • Be careful because each are connected to the camera by a ribbon.

Move the menu button panel to the right as well as the screen.

Be careful because each are connected to the camera by a ribbon.

Step 7

  • Remove two more 3.2 mm screws on the silver panel using your Phillips #000 Screwdriver.

Remove two more 3.2 mm screws on the silver panel using your Phillips #000 Screwdriver.

Step 8

  • Remove the silver panel.

Remove the silver panel.

Step 9

  • Flip the screen back over.
  • Using the plastic open tool, flip open the black retaining plastic piece holding the larger ribbon in place.

Flip the screen back over.

Using the plastic open tool, flip open the black retaining plastic piece holding the larger ribbon in place.

Step 10

  • Carefully detach both ribbons by gently pulling one at a time.
  • The thinner ribbon isn’t secured with a connector and you are able to pull it straight out.
  • Be sure to pull gently as you do not want to break either ribbon.

Carefully detach both ribbons by gently pulling one at a time.

The thinner ribbon isn’t secured with a connector and you are able to pull it straight out.

Be sure to pull gently as you do not want to break either ribbon.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 2 other contributors 


                    Casey Bernier

Member since: 03/04/2016

128 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UMass Dartmouth, Team 6-2, Bhusal Spring 2016                        

                                                  Member of UMass Dartmouth, Team 6-2, Bhusal Spring 2016 



                    UMASSD-BHUSAL-S16S6G2                     


                                            4 Members                     


                                            8 Guides authored

Gerald Heidrich - Jan 12, 2018

Reply

Broke my screen, bought a new one on the internet (ebay) and used this tutorial for replacement.

Good photos and every step is clear to follow