Samsung Yp P3 Battery Replacement Repair Guide

Difficulty

Moderate

Steps

8

Time Required

                          10 minutes            

Sections

3

• Case Backplate
• 3 steps
• Printed Circuit Board
• 4 steps
• Battery
• 1 step

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

• BackSamsung YP-P3

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Case Backplate               

• Pry up the small black piece of plastic located between the volume [-] button and the HOLD/ON button.

Pry up the small black piece of plastic located between the volume [-] button and the HOLD/ON button.

1024

Step 2

• Underneath the piece of plastic you just removed, there is a small screw (Phillips #000, 2.0 mm long). Use a Phillips #000 screwdriver to remove it.

Underneath the piece of plastic you just removed, there is a small screw (Phillips #000, 2.0 mm long). Use a Phillips #000 screwdriver to remove it.

Step 3

• Push on the backplate with both thumbs, sliding it towards the top of the device.
• Once it begins to move, lift up slightly. You can then slide the backplate all the way off.

Push on the backplate with both thumbs, sliding it towards the top of the device.

Once it begins to move, lift up slightly. You can then slide the backplate all the way off.

Step 4

              Printed Circuit Board               

• Before removing the circuit board, we must remove the ribbon-like wires attached to two sides of the circuit board.
• There are two screws (Phillips #000, 2.0 mm long) holding in the circuit board. Use a Phillips #000 screwdriver to take out those screws.

Before removing the circuit board, we must remove the ribbon-like wires attached to two sides of the circuit board.

There are two screws (Phillips #000, 2.0 mm long) holding in the circuit board. Use a Phillips #000 screwdriver to take out those screws.

Step 5

• The battery is also attached to the circuit board by a cable. The cable is difficult to disconnect with both components in place. It’s best to lift the circuit board out partially to give yourself more room to disconnect the connector.
• The wire that is connected to the circuit board is connected by a plastic piece with two metal prongs.
• Use the pointy end of the spudger to place in between the computer board and the plastic piece and gently pry the prongs away from the circuit board.

The battery is also attached to the circuit board by a cable. The cable is difficult to disconnect with both components in place. It’s best to lift the circuit board out partially to give yourself more room to disconnect the connector.

The wire that is connected to the circuit board is connected by a plastic piece with two metal prongs.

Use the pointy end of the spudger to place in between the computer board and the plastic piece and gently pry the prongs away from the circuit board.

Step 6

• Disconnect the battery connector, and then lift the circuit board up.

Disconnect the battery connector, and then lift the circuit board up.

Step 7

• Finally, disconnect the ribbon cable on the bottom of the circuit board. You can then lift the circuit board all the way out.

Finally, disconnect the ribbon cable on the bottom of the circuit board. You can then lift the circuit board all the way out.

Step 8

              Battery               

• Use the spudger to carefully pry up the battery. The battery is attached with a few spots of glue, so it may not move at first.

Use the spudger to carefully pry up the battery. The battery is attached with a few spots of glue, so it may not move at first.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Sandra Freeman                     

Member since: 02/24/2014

118 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       Michigan Tech, Team 5-7, Lauer Spring 2014                        

                                                  Member of Michigan Tech, Team 5-7, Lauer Spring 2014 



                    MTU-LAUER-S14S5G7                     


                                            3 Members                     


                                            2 Guides authored                     

dbgarlikov - Jan 13, 2017

Reply

I had to replace the battery two years ago and again today. This guide made it very easy for me. I was able to change batteries without completely removing the circuit board, but did remove the two screws and ribbon cables on the top of the board to lift up one end of the board.

Thanks for creating this guide!

Paul Rominger - Dec 4, 2018

Reply

Well done, thank you, now to find a digitizer screen, do you know?