Difficulty

Moderate

Steps

6

Time Required

                          20 - 45 minutes

Sections

1

  • Earpiece
  • 6 steps

Flags

2

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Confusing Text

Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!

  • BackSanyo SCP-8100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

You will need to open the top panel by pulling out four stickers that hides the four screws.

  • Note: You will need to use a push pin to pull out the stickers. Using a spudger or an opening tool will not be sufficient enough. They are too thick to use and will make it difficult to use.

What you need

Step 1

              Earpiece
  • Open the phone and remove the four stickers that hide the four 0.5 mm screws.
  • On the bottom two, use a push pin to pull out the stickers.
  • Do this slowly and gently. You may damage the phone screen or tear the sticker.

Open the phone and remove the four stickers that hide the four 0.5 mm screws.

On the bottom two, use a push pin to pull out the stickers.

Do this slowly and gently. You may damage the phone screen or tear the sticker.

1024

Step 2

  • For the top two, use the same push pin and gently pull out the stickers.
  • These are a bit harder to pull out, so you might need to use more force. However, be gentle or else you may tear the rubber off of the sticker instead of the whole plug.

For the top two, use the same push pin and gently pull out the stickers.

These are a bit harder to pull out, so you might need to use more force. However, be gentle or else you may tear the rubber off of the sticker instead of the whole plug.

Step 3

  • Use the Tri-Wing Y1 screwdriver to unscrew the now uncovered four 0.5 mm screws.

Use the Tri-Wing Y1 screwdriver to unscrew the now uncovered four 0.5 mm screws.

Step 4

  • Use the opening tool to pry open the front panel.
  • You might need to use some force. If it won’t budge, try the other side of the panel. You may need to pry open more than one spot to get it completely open.
  • Don’t completely remove the panel, it is still connected to the phone.

Use the opening tool to pry open the front panel.

You might need to use some force. If it won’t budge, try the other side of the panel. You may need to pry open more than one spot to get it completely open.

Don’t completely remove the panel, it is still connected to the phone.

Step 5

  • Use tweezers to detach the plastic connector.
  • With the tweezers, pull the wires from the plastic clamp.

Use tweezers to detach the plastic connector.

With the tweezers, pull the wires from the plastic clamp.

Step 6

  • Use the opening tool to pull the earpiece off of the top panel.
  • You may need to use some force to take this out.

Use the opening tool to pull the earpiece off of the top panel.

You may need to use some force to take this out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Irenz Afable

Member since: 04/15/2013

49 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 10-41, Amido Spring 2013                        

                                                  Member of Cal Poly, Team 10-41, Amido Spring 2013 



                    CPSU-AMIDO-S13S10G41                     


                                            4 Members                     


                                            12 Guides authored