Difficulty

Moderate

Steps

9

Time Required

                          30 - 45 minutes

Sections

3

  • Battery
  • 1 step
  • Back Panel
  • 4 steps
  • Keypad
  • 4 steps

Flags

0

  • BackSanyo SCP-8100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

  • Note: In order to pull out the plug on the back of the phone that is hiding one of the screw, you will need to use a push pin. A spudger or opening tool are too thick to take it out.

What you need

Step 1

              Battery
  • Push and hold the button on the back toward the direction of the arrow to unlock the battery.
  • Lift and remove the battery from the back of the phone.

Push and hold the button on the back toward the direction of the arrow to unlock the battery.

Lift and remove the battery from the back of the phone.

1024

Step 2

              Back Panel
  • Using a push pin, pull out the plug on the back, located under the antenna.
  • You may try to use a spudger or opening tool, however, you may damage the plug because those tools are too thick.

Using a push pin, pull out the plug on the back, located under the antenna.

You may try to use a spudger or opening tool, however, you may damage the plug because those tools are too thick.

Step 3

  • Unscrew the four 6mm long screws with a Tri-Wing Y1 screwdriver.

Unscrew the four 6mm long screws with a Tri-Wing Y1 screwdriver.

Step 4

  • Use a plastic opening tool to pry the back panel along the edges.
  • You may need to apply some force when prying.

Use a plastic opening tool to pry the back panel along the edges.

You may need to apply some force when prying.

Step 5

  • While removing the back panel, take out the rubber cover on each side.

While removing the back panel, take out the rubber cover on each side.

Step 6

              Keypad
  • Pull the volume and camera buttons off from the side of the phone.

Pull the volume and camera buttons off from the side of the phone.

Step 7

  • Pull the gray frame covering the charging port from the bottom of the phone.

Pull the gray frame covering the charging port from the bottom of the phone.

Step 8

  • Use the opening tool to lift the motherboard up from the phone.
  • Be careful and pry the motherboard off slowly. The motherboard will be attached to the phone at the top by a metal ribbon.

Use the opening tool to lift the motherboard up from the phone.

Be careful and pry the motherboard off slowly. The motherboard will be attached to the phone at the top by a metal ribbon.

Step 9

  • Flip open the phone, exposing the keypad.
  • Use the opening tool to push the buttons from the bottom to lift the rubber keypad up.
  • Pull the keypad out of the phone.

Flip open the phone, exposing the keypad.

Use the opening tool to push the buttons from the bottom to lift the rubber keypad up.

Pull the keypad out of the phone.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Irenz Afable

Member since: 04/15/2013

49 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 10-41, Amido Spring 2013                        

                                                  Member of Cal Poly, Team 10-41, Amido Spring 2013 



                    CPSU-AMIDO-S13S10G41                     


                                            4 Members                     


                                            12 Guides authored