Difficulty

Moderate

Steps

12

Time Required

                          20 minutes

Sections

3

  • Battery
  • 4 steps
  • Outer Casing
  • 5 steps
  • LCD Display
  • 3 steps

Flags

1

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

  • BackSanyo VPC-T850

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Make sure the camera is powered off by pressing and holding the small, square button embedded in the top rim of the camera.

Make sure the camera is powered off by pressing and holding the small, square button embedded in the top rim of the camera.

1024

Step 2

  • Locate the hatch found on the bottom of the camera.
  • Open the hatch by gripping the small notch and sliding it outwards.

Locate the hatch found on the bottom of the camera.

Open the hatch by gripping the small notch and sliding it outwards.

Step 3

  • Push the small, plastic arm out of the way to free the battery.
  • The battery is spring loaded and will pop out slightly when the arm is moved.

Push the small, plastic arm out of the way to free the battery.

The battery is spring loaded and will pop out slightly when the arm is moved.

Step 4

  • Pull the battery out of the camera and close the hatch.
  • To reinsert, there is a triangle on the battery indicating which direction to slide it in.

Pull the battery out of the camera and close the hatch.

To reinsert, there is a triangle on the battery indicating which direction to slide it in.

Step 5

              Outer Casing
  • Using your Phillips #000 Screwdriver, remove the eight screws located around the sides and bottom of the camera.
  • Be sure to keep track of the side each screw comes from, as they come in different lengths.

Using your Phillips #000 Screwdriver, remove the eight screws located around the sides and bottom of the camera.

Be sure to keep track of the side each screw comes from, as they come in different lengths.

Step 6

  • Orient the camera so the display is facing up.
  • Gently pull off the rear panel surrounding the display.
  • There are still three green wires connecting the panel to the rest of the camera.
  • Use your prying tool if you have difficulties removing the panel by hand.

Orient the camera so the display is facing up.

Gently pull off the rear panel surrounding the display.

There are still three green wires connecting the panel to the rest of the camera.

Use your prying tool if you have difficulties removing the panel by hand.

Step 7

  • Remove the eight black screws connecting the keypad circuit board to the rear panel.

Remove the eight black screws connecting the keypad circuit board to the rear panel.

Step 8

  • With a plastic opening tool, gently remove the chrome framing on the left and right sides of the camera.

With a plastic opening tool, gently remove the chrome framing on the left and right sides of the camera.

Step 9

  • Flip the camera over so the lens is facing up.
  • Gently lift up the front panel to remove it from the rest of the camera.
  • Use your plastic opening tool if you have difficulties removing the panel by hand.

Flip the camera over so the lens is facing up.

Gently lift up the front panel to remove it from the rest of the camera.

Use your plastic opening tool if you have difficulties removing the panel by hand.

Step 10

              LCD Display
  • Flip the device over to where the display is located.
  • Using your plastic opening tool, lift the display out of its metal housing.

Flip the device over to where the display is located.

Using your plastic opening tool, lift the display out of its metal housing.

Step 11

  • Locate the orange ribbon connecting the display to the camera.
  • Using your plastic opening tool, gently lift the black bar holding the orange ribbon to the camera.

Locate the orange ribbon connecting the display to the camera.

Using your plastic opening tool, gently lift the black bar holding the orange ribbon to the camera.

Step 12

  • With two fingers held firmly on the display, gently pull the orange ribbon out of the camera.
  • Pull slowly to avoid severing the orange ribbon from the display.

With two fingers held firmly on the display, gently pull the orange ribbon out of the camera.

Pull slowly to avoid severing the orange ribbon from the display.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Devin Farnsworth

Member since: 10/29/2015

101 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       UMass Dartmouth, Team 5-5, Gulbrandsen Fall 2015                        

                                                  Member of UMass Dartmouth, Team 5-5, Gulbrandsen Fall 2015 



                    UMASSD-GULBRANDSEN-F15S5G5                     


                                            3 Members                     


                                            10 Guides authored