Scanner Head Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Scanner Tray
9 steps
Scanner Head
3 steps

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

BackHP PSC 2410 Photosmart All In One
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Remove Back Panel

Remove the back panel by inserting your fingers into the indentations next to the tabs. Press the tabs inward towards each other while pulling the back panel toward you.

Remove the back panel by inserting your fingers into the indentations next to the tabs. Press the tabs inward towards each other while pulling the back panel toward you.

1024

Step 2

              Remove Inner Back Pannel

Using the T10 Torx Security Bit Screwdriver, unscrew the screws on the upper left and right corners of the inner panel to remove the inner back panel.

Using the T10 Torx Security Bit Screwdriver, unscrew the screws on the upper left and right corners of the inner panel to remove the inner back panel.

Step 3

              Remove Upper Portion

Press down on the two plastic hinges to remove the upper portion of printer.

Press down on the two plastic hinges to remove the upper portion of printer.

Step 4

              Unplug Speaker Wire

Grasp the plastic plug on the end of the speaker wire, then gently pull the plug away from the printer until the wire is removed.

Grasp the plastic plug on the end of the speaker wire, then gently pull the plug away from the printer until the wire is removed.

Step 5

              Removing Scanner Tray

Rotate the printer so the paper tray is facing towards you.
Gently lift the scanner tray up and away from the printer.
Press the gray plastic tabs inward to release the tabs from the printer.

Rotate the printer so the paper tray is facing towards you.

Gently lift the scanner tray up and away from the printer.

Press the gray plastic tabs inward to release the tabs from the printer.

Step 6

              Removing Scanner Tray - cont.

Returning to the back of the printer, remove the scanner from the back hinges.
With pressure applied, the scanner will detach easily.

Returning to the back of the printer, remove the scanner from the back hinges.

With pressure applied, the scanner will detach easily.

Step 7

Gently grasp and unplug the two white ribbon cables from the printer body.
Be sure to grasp the cable at the connector and not to pull on the wires themselves.

Gently grasp and unplug the two white ribbon cables from the printer body.

Be sure to grasp the cable at the connector and not to pull on the wires themselves.

Step 8

Unplug the white plastic multi-wire connector (with orange, black, red, and brown wires) from it’s port.
Be sure to grasp the white connector and not to pull on the wires themselves.

Unplug the white plastic multi-wire connector (with orange, black, red, and brown wires) from it’s port.

Be sure to grasp the white connector and not to pull on the wires themselves.

Step 9

              Detaching the Scanner Tray

Detach the scanner tray from the printer by lifting the scanner tray off the printer body.

Detach the scanner tray from the printer by lifting the scanner tray off the printer body.

Step 10

              Detaching the Scanner Head

Detach the white ribbon wire from the scanner head by pulling gently at the connection.

Detach the white ribbon wire from the scanner head by pulling gently at the connection.

Step 11

              Removing the Scanner Head

Lift the gray drive belt from the black tab to disconnect the drive belt from the scanner head.
Remove the scanner head from the scanner by gently rotating and then lifting.

Lift the gray drive belt from the black tab to disconnect the drive belt from the scanner head.

Remove the scanner head from the scanner by gently rotating and then lifting.

Step 12

              Adding New Scanner Head

Place the new scanner head in the scanner tray by fastening the drive belt into the black tab.
Make sure the tab on the outer portion of the gray drive belt is fastened.
Once the drive belt is secured, rotate the scanner head back into position.
Re-attach the white ribbon wire to the connection from Step 10.

Place the new scanner head in the scanner tray by fastening the drive belt into the black tab.

Make sure the tab on the outer portion of the gray drive belt is fastened.

Once the drive belt is secured, rotate the scanner head back into position.

Re-attach the white ribbon wire to the connection from Step 10.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 9 other contributors

                    Mackenzie Billings

Member since: 04/05/2011

541 Reputation

                                      2 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 12-31, Maness Spring 2011                        

                                                  Member of Cal Poly, Team 12-31, Maness Spring 2011 



                    CPSU-MANESS-S11S12G31                     


                                            5 Members                     


                                            9 Guides authored

Nichelle King - Aug 11, 2016

Ok, but where do I purchase a new scanner head???

Action Shots#

Introduction#

What you need#

Team#

Action Shots

Introduction

What you need

Team