Difficulty

Easy

Steps

9

Time Required

                          5 - 10 minutes

Sections

2

  • Opening Case
  • 5 steps
  • Separating Rear Board
  • 4 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • Back8BitDo SN30 Pro+ Controller

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove Battery
  • Place the controller face down.
  • Remove the battery cover.
  • Remove rechargeable battery or AA batteries.

Place the controller face down.

Remove the battery cover.

Remove rechargeable battery or AA batteries.

1024

Step 2

              Remove Trigger Buttons
  • Remove L2 and R2 trigger buttons by pushing them away from the grips.

Remove L2 and R2 trigger buttons by pushing them away from the grips.

Step 3

              Remove Screws
  • Use Tweezers to uncover two screws under the label in the battery compartment.
  • Use a T6 screwdriver to remove the four 7.3 mm screws securing the rear cover.

Use Tweezers to uncover two screws under the label in the battery compartment.

Use a T6 screwdriver to remove the four 7.3 mm screws securing the rear cover.

Step 4

              Unclip Covers
  • At the end of each grip, pry apart the covers.
  • Use fingernail or opening pick to undo the two top clips.
  • One clip next to L button.
  • One clip next to R button
  • Undo the final clip between the joysticks.

At the end of each grip, pry apart the covers.

Use fingernail or opening pick to undo the two top clips.

One clip next to L button.

One clip next to R button

Undo the final clip between the joysticks.

Step 5

              Separate Covers
  • Carefully move the rear cover away and from the front cover. Place it to the left.
  • Do not completely separate. The two halves are still attached via a white ribbon cable.

Carefully move the rear cover away and from the front cover. Place it to the left.

Do not completely separate. The two halves are still attached via a white ribbon cable.

Step 6

              Remove Ribbon Cable
  • Unlock the ribbon cable by push open the black plastic tab.
  • The tab will slide about 1.5mm
  • Pull the ribbon cable out of the connector in the direction of the cable.

Unlock the ribbon cable by push open the black plastic tab.

The tab will slide about 1.5mm

Pull the ribbon cable out of the connector in the direction of the cable.

Step 7

              Remove Caps
  • Grab the top and pull straight up on the joystick cap. Pulling out the caps one-by-one.

Grab the top and pull straight up on the joystick cap. Pulling out the caps one-by-one.

Step 8

              Remove Screws
  • Use a Phillips screwdriver to remove the nine 5.2 mm screws securing the rear circuit board.
  • Four around the Right stick
  • Four around the Left stick
  • One next to the Battery connector

Use a Phillips screwdriver to remove the nine 5.2 mm screws securing the rear circuit board.

Four around the Right stick

Four around the Left stick

One next to the Battery connector

Step 9

              Separate Rear Board
  • Pull the two rumble motors out of their housings.
  • Grab the analog sticks to pull out the circuit board

Pull the two rumble motors out of their housings.

Grab the analog sticks to pull out the circuit board

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    Brian W

Member since: 12/21/2011

1,080 Reputation

                                      8 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges