Serenelife Treadmill Slftrd20 Belt Adjustment Repair Guide

Difficulty

Easy

Steps

8

Time Required

                          20 minutes            

Sections

1

• SereneLife Treadmill SLFTRD20 Belt Adjustment
• 8 steps

Flags

0

• BackTreadmill

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

If your SereneLife Treadmill Belt (model SLFTRD20) has begun to stretch and slip after extended use and requires an adjustment, follow this guide.

The running belt is the most important component that must constantly be centered in order to utilize the Treadmill. If the running belt starts to slide or extend to the side, the treadmill is rendered useless.

Step 2 requires you to ensure that the treadmill belt is running at the lowest speed possible, or else the belt will not be centered. However in step 6, it shows that Treadmill should be turned off before tightening the belt, so don’t try to mix up both of these steps.

What you need

Step 1

              SereneLife Treadmill SLFTRD20 Belt Adjustment               

• Turn on the main power switch.

Turn on the main power switch.

1024

Step 2

• Begin by pressing the “Start” button on the machine.
• Let the treadmill belt run at the lowest setting.

Begin by pressing the “Start” button on the machine.

Let the treadmill belt run at the lowest setting.

Step 3

• In order to locate the roller adjustment bolts, try locating the rear left cover and rear right cover.

In order to locate the roller adjustment bolts, try locating the rear left cover and rear right cover.

Step 4

• Remove the attached rear left and right covers from the treadmill.
• After removing the rear covers, you’ll be able to see the adjustment bolts.

Remove the attached rear left and right covers from the treadmill.

After removing the rear covers, you’ll be able to see the adjustment bolts.

Step 5

• Before we begin it’s important to determine which side the belt is shifting towards.
• If the belt is shifting to the right, then turn the right adjustment bolt to turn 1/4 clockwise. If the belt is shifting to the left, then turn the left adjustment bolt to turn 1/4 clockwise.
• Place the Allen wrench in the left rear roller bolt.
• Turn the left roller bolt adjustment to turn one-fourth clockwise.
• Now stop and wait for the belt to begin to center itself.
• You must wait for the belt to re-center between each adjustment to ensure that you do not overcorrect the belt.

Before we begin it’s important to determine which side the belt is shifting towards.

If the belt is shifting to the right, then turn the right adjustment bolt to turn 1/4 clockwise. If the belt is shifting to the left, then turn the left adjustment bolt to turn 1/4 clockwise.

Place the Allen wrench in the left rear roller bolt.

Turn the left roller bolt adjustment to turn one-fourth clockwise.

Now stop and wait for the belt to begin to center itself.

You must wait for the belt to re-center between each adjustment to ensure that you do not overcorrect the belt.

Step 6

• In order to fix the slipping belt during use, we need to turn off and unplug the Treadmill.

In order to fix the slipping belt during use, we need to turn off and unplug the Treadmill.

Step 7

• Place the Allen wrench in the left roller bolt and turn it 1/4 clockwise to tighten the belt.
• Repeat on the right side of the roller bolt in the same way.

Place the Allen wrench in the left roller bolt and turn it 1/4 clockwise to tighten the belt.

Repeat on the right side of the roller bolt in the same way.

Step 8

• Attach the rear covers onto the left side and right side of the frames.
• Turn the main power switch back on and run the treadmill at the lowest speed.
• Run on the treadmill to determine if the belt is still slipping or not.
• Repeat this procedure until the belt no longer slips.

Attach the rear covers onto the left side and right side of the frames.

Turn the main power switch back on and run the treadmill at the lowest speed.

Run on the treadmill to determine if the belt is still slipping or not.

Repeat this procedure until the belt no longer slips.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    Alina Abbas                     

Member since: 07/03/2021

211 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       York University, Team S2-G2, Melo-Thaiss Summer 2021                        

                                                  Member of York University, Team S2-G2, Melo-Thaiss Summer 2021 



                    YORK-MELO-THAISS-SU21S2G2                     


                                            1 Member                     


                                            1 Guide authored