Difficulty
Difficult
Steps
13
Time Required
30 - 40 minutes
Sections
3
- External Pieces
- 4 steps
- Filter
- 3 steps
- Power Cable/Connector
- 6 steps
Flags
0
BackShark DuoClean Powered Lift-Away Speed
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
External Pieces
- Press the Hose Release button and pull back to detach the hose.
Press the Hose Release button and pull back to detach the hose.
1024
Step 2
- Press the Wand Release button and pull up on the metal tube to remove the entire hose.
Press the Wand Release button and pull up on the metal tube to remove the entire hose.
Step 3
- Press the Lift Away button and pull up on the handle to separate the top of the vacuum from the bottom.
Press the Lift Away button and pull up on the handle to separate the top of the vacuum from the bottom.
Step 4
- Pull up on the extra brush pieces to remove them from the vacuum.
Pull up on the extra brush pieces to remove them from the vacuum.
Step 5
Filter
- Pull up on the Dustbin Release button, and pull up on the handle to detach the dustbin.
Pull up on the Dustbin Release button, and pull up on the handle to detach the dustbin.
Step 6
- Pull up on the filter tab to remove the large foam filter.
Pull up on the filter tab to remove the large foam filter.
Step 7
- Pull up on the small tab to remove the filter pad.
Pull up on the small tab to remove the filter pad.
Step 8
Power Cable/Connector
- Use the T20 screwdriver to remove the two 12 mm screws by turning counterclockwise.
- Use the T20 screwdriver to remove the two 17 mm screws by turning counterclockwise.
- Use the T20 screwdriver to remove the two 14 mm screws by turning counterclockwise.
Use the T20 screwdriver to remove the two 12 mm screws by turning counterclockwise.
Use the T20 screwdriver to remove the two 17 mm screws by turning counterclockwise.
Use the T20 screwdriver to remove the two 14 mm screws by turning counterclockwise.
Step 9
- Use the T20 screwdriver to remove the three 15 mm screws by turning counterclockwise.
- Use the T10 screwdriver to remove the one 17 mm screw by turning counterclockwise.
Use the T20 screwdriver to remove the three 15 mm screws by turning counterclockwise.
Use the T10 screwdriver to remove the one 17 mm screw by turning counterclockwise.
Step 10
- Use the T20 screwdriver to remove the four 14 mm screws from the bottom of the vacuum by turning counterclockwise.
- The grey plastic cylinders will detach.
Use the T20 screwdriver to remove the four 14 mm screws from the bottom of the vacuum by turning counterclockwise.
The grey plastic cylinders will detach.
Step 11
- Use the metal spudger to pry off the back panel.
- Be careful not to break or snap any plastic.
Use the metal spudger to pry off the back panel.
Be careful not to break or snap any plastic.
Step 12
- On the white cap holding the wire, use the T20 screwdriver to remove the two 12 mm screws by turning counter-clockwise .
- Remove the white cap by pulling it off the device.
On the white cap holding the wire, use the T20 screwdriver to remove the two 12 mm screws by turning counter-clockwise .
Remove the white cap by pulling it off the device.
Step 13
- Use wire cutters to detach the power cord by cutting the black and white wires.
- For reassembly, you must strip and then rewire the new power cord using wire strippers and end caps. Use this guide to learn more about stripping wires.
Use wire cutters to detach the power cord by cutting the black and white wires.
For reassembly, you must strip and then rewire the new power cord using wire strippers and end caps. Use this guide to learn more about stripping wires.
To reassemble your device, you must rewire a new power cord, then follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 5 other contributors
Catie Halvorsen
Member since: 10/08/2018
695 Reputation
5 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team S17-G4, White Fall 2018
Member of Cal Poly, Team S17-G4, White Fall 2018
CPSU-WHITE-F18S17G4
4 Members
16 Guides authored
David Nancoo - Dec 20, 2021
Reply
Very well done. You need a few stars,/.
