Shark Iq Av993 Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 minutes

Sections

Battery
2 steps
Bumper
3 steps
Wheels
2 steps
Roller Brush
3 steps
Motherboard
9 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

BackShark IQ AV993
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Unscrew the two 14 mm screws on the battery panel using a Phillips #1 screwdriver.

Unscrew the two 14 mm screws on the battery panel using a Phillips #1 screwdriver.

1024

Step 2

Gently pull the white tabs on the battery straight upward.
There is a clip inserted into a plastic housing via wiring. Disconnect the battery by pressing in the clip.
Don’t pull up on the battery too hard as a wire connects to the robot. Don’t want to damage the wire here.
Remove the battery from the device.

Gently pull the white tabs on the battery straight upward.

There is a clip inserted into a plastic housing via wiring. Disconnect the battery by pressing in the clip.

Don’t pull up on the battery too hard as a wire connects to the robot. Don’t want to damage the wire here.

Remove the battery from the device.

Step 3

              Bumper

Remove the five 10 mm screws from the bottom of the device using a T15 Torx screwdriver.

Remove the five 10 mm screws from the bottom of the device using a T15 Torx screwdriver.

Step 4

Pry both ends of the black piece to snap it out of place.

Pry both ends of the black piece to snap it out of place.

Step 5

Use both hands to lift the device.
The front bumper that is seated on the device will fall off.
This is completely normal, as the screws and the bottom holder are the only things holding the bumper in place.

Use both hands to lift the device.

The front bumper that is seated on the device will fall off.

This is completely normal, as the screws and the bottom holder are the only things holding the bumper in place.

Step 6

              Wheels

Flip over the vacuum so that the bottom is facing upwards.
Remove the five 14 mm screws using a T20 Torx screwdriver.

Flip over the vacuum so that the bottom is facing upwards.

Remove the five 14 mm screws using a T20 Torx screwdriver.

Step 7

Pull upward on the wheel to remove the wheel housing.
Carefully remove this as there is a clip connecting to the wheel.
Press the tab on the clip and slide the wires out of the housing.
Repeat this step and the previous step for the other wheel assembly.

Pull upward on the wheel to remove the wheel housing.

Carefully remove this as there is a clip connecting to the wheel.

Press the tab on the clip and slide the wires out of the housing.

Repeat this step and the previous step for the other wheel assembly.

Step 8

              Roller Brush

Remove the dust bin from the device by pressing down on the release button and pulling out the tray.

Remove the dust bin from the device by pressing down on the release button and pulling out the tray.

Step 9

Turn the device over so the bottom is facing upwards.
Press on the release tabs located on the roller brush cover.
Remove the cover from the device.

Turn the device over so the bottom is facing upwards.

Press on the release tabs located on the roller brush cover.

Remove the cover from the device.

Step 10

Use your hands to lift the roller brush out of the device.

Use your hands to lift the roller brush out of the device.

Step 11

              Motherboard

Remove the five 14 mm screws from the bottom of the device using a T20 Torx screwdriver.

Remove the five 14 mm screws from the bottom of the device using a T20 Torx screwdriver.

Step 12

Use your hands to lift the bottom of the vacuum away from the top plastic cover.
To lift this section off, you may need to apply slight pressure to the top plastic cover. If not, the cover should fall right off as it just rests on guide pins.

Use your hands to lift the bottom of the vacuum away from the top plastic cover.

To lift this section off, you may need to apply slight pressure to the top plastic cover. If not, the cover should fall right off as it just rests on guide pins.

Step 13

Remove the three 10 mm screws using a Phillips #1 screwdriver.
Off to the right and left sides of the robot you will find one clip leading to a smaller independent board. Remove the singular 9 mm screw using a T15 Torx screwdriver to free the edges of the plastic element holding the motherboard down. Repeat this for the other side.
Detach the white connector from the plastic housing. Repeat this for the other side.
Do not pull on this housing element too hard, as they are not soldered onto the board very well. This could result ripping the housing clean off the board, rendering the device inoperable until reassembly.

Remove the three 10 mm screws using a Phillips #1 screwdriver.

Off to the right and left sides of the robot you will find one clip leading to a smaller independent board. Remove the singular 9 mm screw using a T15 Torx screwdriver to free the edges of the plastic element holding the motherboard down. Repeat this for the other side.

Detach the white connector from the plastic housing. Repeat this for the other side.

Do not pull on this housing element too hard, as they are not soldered onto the board very well. This could result ripping the housing clean off the board, rendering the device inoperable until reassembly.

Step 14

Unplug each of the thirteen connectors from their housings on the motherboard.
Using a spudger may be of assistance to leverage the smaller ones out.
Do not pull/pry on the connectors too hard, as they are not seated onto the motherboard very well. This could result in ripping one of the housings clean off the board, rendering the device inoperable until replacement.

Unplug each of the thirteen connectors from their housings on the motherboard.

Using a spudger may be of assistance to leverage the smaller ones out.

Do not pull/pry on the connectors too hard, as they are not seated onto the motherboard very well. This could result in ripping one of the housings clean off the board, rendering the device inoperable until replacement.

Step 15

This clip holds all the wires in an organized manner and is a part of the plastic housing that needs to be removed.
Take the wires out of this clip so that the plastic cover can be free.

This clip holds all the wires in an organized manner and is a part of the plastic housing that needs to be removed.

Take the wires out of this clip so that the plastic cover can be free.

Step 16

As indicated this is the plastic cover we are trying to remove from the bot, clearly distinctive by the lip.
On either side of the bot, there are clips that insert into the upper plastic housing piece that hold the motherboard down. Popping these pieces off will free this covering, allowing the motherboard to be almost free.

As indicated this is the plastic cover we are trying to remove from the bot, clearly distinctive by the lip.

On either side of the bot, there are clips that insert into the upper plastic housing piece that hold the motherboard down. Popping these pieces off will free this covering, allowing the motherboard to be almost free.

Step 17

Remove the two 10 mm screws using a Phillips #1 screwdriver, freeing the motherboard from the plastic holdings below the board.

Remove the two 10 mm screws using a Phillips #1 screwdriver, freeing the motherboard from the plastic holdings below the board.

Step 18

Upon lifting up the motherboard, which will lift straight up, there is a singular clip that connects the rest of the bot. Unclip this, where the clip is large enough to undo with a finger.
Once this is removed, the motherboard and the plastic it is clipped to can be removed from the rest of the bot.

Upon lifting up the motherboard, which will lift straight up, there is a singular clip that connects the rest of the bot. Unclip this, where the clip is large enough to undo with a finger.

Once this is removed, the motherboard and the plastic it is clipped to can be removed from the rest of the bot.

Step 19

The board is attached to the plastic frame by these spring-loaded clips. Pinch the bottom of these with some tweezers and push the ends through the hole they bore to remove them.
Once these two clips, one on either side, are removed, the motherboard will be independent from the plastic framing, ready to be replaced.

The board is attached to the plastic frame by these spring-loaded clips. Pinch the bottom of these with some tweezers and push the ends through the hole they bore to remove them.

Once these two clips, one on either side, are removed, the motherboard will be independent from the plastic framing, ready to be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Kyle Rhines

Member since: 10/26/2022

504 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       UMass Dartmouth, Team 3-3, Botvin Fall 2022                        

                                                  Member of UMass Dartmouth, Team 3-3, Botvin Fall 2022 



                    UMASSD-BOTVIN-F22S3G3                     


                                            3 Members                     


                                            6 Guides authored

Needs Better Images#

Needs More Images#

Introduction#

What you need#

Team#

Needs Better Images

Needs More Images

Introduction

What you need

Team