Difficulty

Easy

Steps

7

Time Required

                          5 minutes

Sections

3

  • Battery
  • 2 steps
  • Bumper
  • 3 steps
  • Wheels
  • 2 steps

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackShark IQ AV993

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Unscrew the two 14 mm screws on the battery panel using a Phillips #1 screwdriver.

Unscrew the two 14 mm screws on the battery panel using a Phillips #1 screwdriver.

1024

Step 2

  • Gently pull the white tabs on the battery straight upward.
  • There is a clip inserted into a plastic housing via wiring. Disconnect the battery by pressing in the clip.
  • Don’t pull up on the battery too hard as a wire connects to the robot. Don’t want to damage the wire here.
  • Remove the battery from the device.

Gently pull the white tabs on the battery straight upward.

There is a clip inserted into a plastic housing via wiring. Disconnect the battery by pressing in the clip.

Don’t pull up on the battery too hard as a wire connects to the robot. Don’t want to damage the wire here.

Remove the battery from the device.

Step 3

              Bumper
  • Remove the five 10 mm screws from the bottom of the device using a T15 Torx screwdriver.

Remove the five 10 mm screws from the bottom of the device using a T15 Torx screwdriver.

Step 4

  • Pry both ends of the black piece to snap it out of place.

Pry both ends of the black piece to snap it out of place.

Step 5

  • Use both hands to lift the device.
  • The front bumper that is seated on the device will fall off.
  • This is completely normal, as the screws and the bottom holder are the only things holding the bumper in place.

Use both hands to lift the device.

The front bumper that is seated on the device will fall off.

This is completely normal, as the screws and the bottom holder are the only things holding the bumper in place.

Step 6

              Wheels
  • Flip over the vacuum so that the bottom is facing upwards.
  • Remove the five 14 mm screws using a T20 Torx screwdriver.

Flip over the vacuum so that the bottom is facing upwards.

Remove the five 14 mm screws using a T20 Torx screwdriver.

Step 7

  • Pull upward on the wheel to remove the wheel housing.
  • Carefully remove this as there is a clip connecting to the wheel.
  • Press the tab on the clip and slide the wires out of the housing.
  • Repeat this step and the previous step for the other wheel assembly.

Pull upward on the wheel to remove the wheel housing.

Carefully remove this as there is a clip connecting to the wheel.

Press the tab on the clip and slide the wires out of the housing.

Repeat this step and the previous step for the other wheel assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Marc Farah

Member since: 10/26/2022

85 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       UMass Dartmouth, Team 3-3, Botvin Fall 2022                        

                                                  Member of UMass Dartmouth, Team 3-3, Botvin Fall 2022 



                    UMASSD-BOTVIN-F22S3G3                     


                                            3 Members                     


                                            6 Guides authored