Shark Navigator Lift Away Deluxe Nv360 Motherboard Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          40 minutes

Sections

Roller Brush Belt
8 steps
Roller Brush
1 step
Roller Brush Motor
5 steps
Motherboard
6 steps

Flags

BackShark Navigator Lift-Away Deluxe NV360
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Roller Brush Belt

Lay the vacuum down by hand and locate the roller brush underneath the vacuum cleaner.

Lay the vacuum down by hand and locate the roller brush underneath the vacuum cleaner.

1024

Step 2

Insert the metal spudger between the inside side of the wheel and the plastic body.
Push the metal spudger away from you to pop the wheels out.
Repeat the step to remove the other wheel on the other side.

Insert the metal spudger between the inside side of the wheel and the plastic body.

Push the metal spudger away from you to pop the wheels out.

Repeat the step to remove the other wheel on the other side.

Step 3

Remove the six 15mm screws using the PH1 screwdriver.

Remove the six 15mm screws using the PH1 screwdriver.

Step 4

Move the blue fulcrum connecting the bottom and the main body of the vacuum cleaner back and forth to loosen up crevice between the two halves of the roller brush enclosure.

Move the blue fulcrum connecting the bottom and the main body of the vacuum cleaner back and forth to loosen up crevice between the two halves of the roller brush enclosure.

Step 5

Insert the plastic opening tool into the crevice between the blue and the dark grey plastic frames enclosing the roller brush.
Apply an outward force throughout and all around the gap in order to separate the two plastic frames.

Insert the plastic opening tool into the crevice between the blue and the dark grey plastic frames enclosing the roller brush.

Apply an outward force throughout and all around the gap in order to separate the two plastic frames.

Step 6

Lift the grey frame off the bottom of the vacuum cleaner with your hands and place it on a flat surface.

Lift the grey frame off the bottom of the vacuum cleaner with your hands and place it on a flat surface.

Step 7

Lift the roller brush slightly upwards using your hand.
Take one side of the black roller brush belt off by pulling it over the end of the roller brush with your other hand.

Lift the roller brush slightly upwards using your hand.

Take one side of the black roller brush belt off by pulling it over the end of the roller brush with your other hand.

Step 8

Remove the roller brush belt with your hands by sliding it of the end of the motor.

Remove the roller brush belt with your hands by sliding it of the end of the motor.

Step 9

              Roller Brush

Remove the roller brush from the plastic frame using your hands by lifting it away.

Remove the roller brush from the plastic frame using your hands by lifting it away.

Step 10

              Roller Brush Motor

Lift the roller brush motor up and away from its half-cylindrical holder with your hand.

Lift the roller brush motor up and away from its half-cylindrical holder with your hand.

Step 11

Locate the two connectors coming out of the roller brush motor.
Pinch and pull the blue plastic insulation down the wire and away from the motor until the metal connectors are fully exposed.

Locate the two connectors coming out of the roller brush motor.

Pinch and pull the blue plastic insulation down the wire and away from the motor until the metal connectors are fully exposed.

Step 12

Locate the protrusion near the connection between the metal and wire.
Push down on the protrusion with your finger and push the metal connector away from the motor with the metal spudger.

Locate the protrusion near the connection between the metal and wire.

Push down on the protrusion with your finger and push the metal connector away from the motor with the metal spudger.

Step 13

Continue to push on the connector away from the motor with the metal spudger until it is disconnected completely.
Repeat the steps 12-14 for the other wire.

Continue to push on the connector away from the motor with the metal spudger until it is disconnected completely.

Repeat the steps 12-14 for the other wire.

Step 14

Take the motor out and away from the motorized floor brush compartment by hand.

Take the motor out and away from the motorized floor brush compartment by hand.

Step 15

              Motherboard

Locate the two wires that were connected to the roller brush motor.
Remove the white wire from the pass-through hole in the divider of the motorized floor brush compartment.

Locate the two wires that were connected to the roller brush motor.

Remove the white wire from the pass-through hole in the divider of the motorized floor brush compartment.

Step 16

Remove the black wire from the pass-through hole in the divider of the motorized floor brush compartment.

Remove the black wire from the pass-through hole in the divider of the motorized floor brush compartment.

Step 17

Locate and remove the two 10mm screws on the motherboard with the PH1 screwdriver.

Locate and remove the two 10mm screws on the motherboard with the PH1 screwdriver.

Step 18

Cut the white wire from the motherboard with wire cutters.
Solder the wire connection back together during reassembly.

Cut the white wire from the motherboard with wire cutters.

Solder the wire connection back together during reassembly.

Step 19

Pull the black wire out of the white holder with a pass-through slot using your hands.
Cut the black wire from the motherboard with the wire cutters.
Solder the wire connection back together during reassembly.

Pull the black wire out of the white holder with a pass-through slot using your hands.

Cut the black wire from the motherboard with the wire cutters.

Step 20

Remove the motherboard by lifting it away from the motorized floor brush compartment with your hands.

Remove the motherboard by lifting it away from the motorized floor brush compartment with your hands.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Elena Postupalskaya

Member since: 10/02/2017

1,039 Reputation

                                      6 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team S15-G2, Livingston Fall 2017                        

                                                  Member of Cal Poly, Team S15-G2, Livingston Fall 2017 



                    CPSU-LIVINGSTON-F17S15G2                     


                                            3 Members                     


                                            14 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team