Shark Navigator Lift Away Deluxe Nv360 Power Button Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          35 minutes

Sections

Foam and Felt Filters
5 steps
Power Button
14 steps

Flags

BackShark Navigator Lift-Away Deluxe NV360
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Foam and Felt Filters

Locate the latches on the side of the dust cup, the clear plastic chamber in the center of the vacuum.

Locate the latches on the side of the dust cup, the clear plastic chamber in the center of the vacuum.

1024

Step 2

Pull the bottom of the latch with your hand in an upward direction.
Lift the top of the latch up and away from the dust cup using your hand.
Repeat the above steps with the latch on the other side of the dust cup.

Pull the bottom of the latch with your hand in an upward direction.

Lift the top of the latch up and away from the dust cup using your hand.

Repeat the above steps with the latch on the other side of the dust cup.

Step 3

Lift the dust cup up and away by its handle on the top with your hands.

Lift the dust cup up and away by its handle on the top with your hands.

Step 4

Lift the foam filter up, out, and away with your hands.

Lift the foam filter up, out, and away with your hands.

Step 5

Lift the felt filter up, out, and away with your hands by the tab on the top.

Lift the felt filter up, out, and away with your hands by the tab on the top.

Step 6

              Power Button

Locate the red latch on the side of the vacuum cleaner.
Push the circular region of the latch with your finger.

Locate the red latch on the side of the vacuum cleaner.

Push the circular region of the latch with your finger.

Step 7

Lift this upper plastic body of the vacuum cleaner up with your hands while continuing to press on the circular region of the latch.

Lift this upper plastic body of the vacuum cleaner up with your hands while continuing to press on the circular region of the latch.

Step 8

Locate the lower junction that connects the curved grey plastic tube and the hose coming from the vacuum cleaner’s handle.
Press on the two grey flaps on either side of the hose simultaneously with your fingers and lift the hose out of the plastic cup with your hand.

Locate the lower junction that connects the curved grey plastic tube and the hose coming from the vacuum cleaner’s handle.

Press on the two grey flaps on either side of the hose simultaneously with your fingers and lift the hose out of the plastic cup with your hand.

Step 9

Locate the red latch that was next to the hose from the previous step.
Hold the bottom of vacuum cleaner’s handle and its extension.
Use your other hand to press on the latch.
Lift the handle off the vacuum cleaner.

Locate the red latch that was next to the hose from the previous step.

Hold the bottom of vacuum cleaner’s handle and its extension.

Use your other hand to press on the latch.

Lift the handle off the vacuum cleaner.

Step 10

Remove the two 15mm screws with the PH1 screwdriver located on the bottom side of grey plastic body from which the handle was removed.

Remove the two 15mm screws with the PH1 screwdriver located on the bottom side of grey plastic body from which the handle was removed.

Step 11

Lift the grey compartment out of the main body of the vacuum cleaner by pulling upwards with your hands.

Lift the grey compartment out of the main body of the vacuum cleaner by pulling upwards with your hands.

Step 12

Continue to pull on the grey compartment until it is fully out of the main body of the vacuum.
Place the grey compartment on a surface for the next step.

Continue to pull on the grey compartment until it is fully out of the main body of the vacuum.

Place the grey compartment on a surface for the next step.

Step 13

Peel the sticker away with your hands until the hidden screw hole is fully exposed.

Peel the sticker away with your hands until the hidden screw hole is fully exposed.

Step 14

Locate and remove the five 15mm screws with a PH1 screwdriver.

Locate and remove the five 15mm screws with a PH1 screwdriver.

Step 15

Insert plastic opening tool into the crevice in the middle between the two halves of the grey compartment.
Apply an outward force throughout and all around the gap in order to separate the two plastic halves.

Insert plastic opening tool into the crevice in the middle between the two halves of the grey compartment.

Apply an outward force throughout and all around the gap in order to separate the two plastic halves.

Step 16

Locate the red power button and its red, blue, and black connected wires.
Pinch and pull the red wire’s clear plastic insulator away from the power button with your hands until the metal connector is fully exposed.
Repeat this step for the blue wire.

Locate the red power button and its red, blue, and black connected wires.

Pinch and pull the red wire’s clear plastic insulator away from the power button with your hands until the metal connector is fully exposed.

Repeat this step for the blue wire.

Step 17

Locate the protrusion on the metal connector of the red wire.
Push down on the protrusion with the metal spudger while pushing the connector on the red wire away from the power button with your fingers.
Pull and wiggle the wire away by its connector with your fingers until it is completely detached from the connector on the power button.
Repeat this step for the blue wire

Locate the protrusion on the metal connector of the red wire.

Push down on the protrusion with the metal spudger while pushing the connector on the red wire away from the power button with your fingers.

Pull and wiggle the wire away by its connector with your fingers until it is completely detached from the connector on the power button.

Repeat this step for the blue wire

Step 18

Push down towards the outside on the ledges that are holding the power button inside the grey frame.
Pull on the power button from the outside of the grey compartment with your hands, once the ledges are past the edge of grey frame.

Push down towards the outside on the ledges that are holding the power button inside the grey frame.

Pull on the power button from the outside of the grey compartment with your hands, once the ledges are past the edge of grey frame.

Step 19

Pull the power button a couple inches away from the grey frame with your hands so that you have easy access to the black wire’s connection.
Repeat steps 16 and 17 on the black wire and its connector.
Remove the disconnected power button away from the frame with your hands.

Pull the power button a couple inches away from the grey frame with your hands so that you have easy access to the black wire’s connection.

Repeat steps 16 and 17 on the black wire and its connector.

Remove the disconnected power button away from the frame with your hands.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Elena Postupalskaya

Member since: 10/02/2017

1,039 Reputation

                                      6 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team S15-G2, Livingston Fall 2017                        

                                                  Member of Cal Poly, Team S15-G2, Livingston Fall 2017 



                    CPSU-LIVINGSTON-F17S15G2                     


                                            3 Members                     


                                            14 Guides authored

Mark Snowden - Mar 18, 2019

These instructions are for changing the switch and are great. My question is the switch isn’t listed as a needed part. How can I buy a replacement switch?

James Avey - Nov 11, 2019

search for shark (your model number here) power switch. I found it on amazon and several other places. That’s also how I found these instructions.

Jonathan Steinberg - Jun 29, 2020

Great Instructions, except see notes on step 11 - there seems to be another step required to disconnect grey switch compartment.

Scott Billingsley - Apr 5, 2022

Agree with previous question on Step 11 - half of the compartment will not come out. I thought a wire was jammed somehow. My roller will not work. I took apart the vacuum from the bottom up and it works with direct power to it (with a testing circuit) but as i moved up the electrical system, it seems to be at the switch compartment somewhere. Switch itself seems fine for the main motor, but will not activate the roller. Any ideas?

Kimberlee Smith - Oct 6, 2022

I want to return it, it didn’t work right out of the box!!

Introduction#

What you need#

Team#

Introduction

What you need

Team