Shark Navigator Lift Away Deluxe Nv360 Roller Brush Motor Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Roller Brush Belt
8 steps
Roller Brush
1 step
Roller Brush Motor
5 steps

Flags

BackShark Navigator Lift-Away Deluxe NV360
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Roller Brush Belt

Lay the vacuum down by hand and locate the roller brush underneath the vacuum cleaner.

Lay the vacuum down by hand and locate the roller brush underneath the vacuum cleaner.

1024

Step 2

Insert the metal spudger between the inside side of the wheel and the plastic body.
Push the metal spudger away from you to pop the wheels out.
Repeat the step to remove the other wheel on the other side.

Insert the metal spudger between the inside side of the wheel and the plastic body.

Push the metal spudger away from you to pop the wheels out.

Repeat the step to remove the other wheel on the other side.

Step 3

Remove the six 15mm screws using the PH1 screwdriver.

Remove the six 15mm screws using the PH1 screwdriver.

Step 4

Move the blue fulcrum connecting the bottom and the main body of the vacuum cleaner back and forth to loosen up crevice between the two halves of the roller brush enclosure.

Move the blue fulcrum connecting the bottom and the main body of the vacuum cleaner back and forth to loosen up crevice between the two halves of the roller brush enclosure.

Step 5

Insert the plastic opening tool into the crevice between the blue and the dark grey plastic frames enclosing the roller brush.
Apply an outward force throughout and all around the gap in order to separate the two plastic frames.

Insert the plastic opening tool into the crevice between the blue and the dark grey plastic frames enclosing the roller brush.

Apply an outward force throughout and all around the gap in order to separate the two plastic frames.

Step 6

Lift the grey frame off the bottom of the vacuum cleaner with your hands and place it on a flat surface.

Lift the grey frame off the bottom of the vacuum cleaner with your hands and place it on a flat surface.

Step 7

Lift the roller brush slightly upwards using your hand.
Take one side of the black roller brush belt off by pulling it over the end of the roller brush with your other hand.

Lift the roller brush slightly upwards using your hand.

Take one side of the black roller brush belt off by pulling it over the end of the roller brush with your other hand.

Step 8

Remove the roller brush belt with your hands by sliding it of the end of the motor.

Remove the roller brush belt with your hands by sliding it of the end of the motor.

Step 9

              Roller Brush

Remove the roller brush from the plastic frame using your hands by lifting it away.

Remove the roller brush from the plastic frame using your hands by lifting it away.

Step 10

              Roller Brush Motor

Lift the roller brush motor up and away from its half-cylindrical holder with your hand.

Lift the roller brush motor up and away from its half-cylindrical holder with your hand.

Step 11

Locate the two connectors coming out of the roller brush motor.
Pinch and pull the blue plastic insulation down the wire and away from the motor until the metal connectors are fully exposed.

Locate the two connectors coming out of the roller brush motor.

Pinch and pull the blue plastic insulation down the wire and away from the motor until the metal connectors are fully exposed.

Step 12

Locate the protrusion near the connection between the metal and wire.
Push down on the protrusion with your finger and push the metal connector away from the motor with the metal spudger.

Locate the protrusion near the connection between the metal and wire.

Push down on the protrusion with your finger and push the metal connector away from the motor with the metal spudger.

Step 13

Continue to push on the connector away from the motor with the metal spudger until it is disconnected completely.
Repeat the steps 12-14 for the other wire.

Continue to push on the connector away from the motor with the metal spudger until it is disconnected completely.

Repeat the steps 12-14 for the other wire.

Step 14

Take the motor out and away from the motorized floor brush compartment by hand.

Take the motor out and away from the motorized floor brush compartment by hand.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 3 other contributors

                    Elena Postupalskaya

Member since: 10/02/2017

1,039 Reputation

                                      6 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team S15-G2, Livingston Fall 2017                        

                                                  Member of Cal Poly, Team S15-G2, Livingston Fall 2017 



                    CPSU-LIVINGSTON-F17S15G2                     


                                            3 Members                     


                                            14 Guides authored

Matt Trainum - Mar 7, 2020

Well this looks really handy to read! Where can I get a replacement motor? Any helpful links!? :)

bradschulz - Sep 19, 2020

Yes! Where do I buy the motor?

mantylajeremy - May 24, 2022

Where do you find the motor? Any part numbers??

Andre du Plessis - Jun 13, 2022

Where to find a motor? Shark has work to do!!!

Introduction#

What you need#

Team#

Introduction

What you need

Team