Shark Navigator Lift Away Deluxe Nv500 Roller Brush Belt Replacement Repair Guide

Difficulty

Moderate

Steps

8

Time Required

                          15 minutes            

Sections

1

• Roller Brush Belt
• 8 steps

Flags

0

• BackShark Navigator Lift-Away Deluxe NV500

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Roller Brush Belt               

• Lay the vacuum down by hand and locate the roller brush underneath the vacuum cleaner.

Lay the vacuum down by hand and locate the roller brush underneath the vacuum cleaner.

1024

Step 2

• Insert the metal spudger between the inside side of the wheel and the plastic body.
• Push the metal spudger away from you to pop the wheels out.
• Repeat the step to remove the other wheel on the other side.

Insert the metal spudger between the inside side of the wheel and the plastic body.

Push the metal spudger away from you to pop the wheels out.

Repeat the step to remove the other wheel on the other side.

Step 3

• Remove the six 15mm screws using the PH1 screwdriver.

Remove the six 15mm screws using the PH1 screwdriver.

Step 4

• Move the blue fulcrum connecting the bottom and the main body of the vacuum cleaner back and forth to loosen up crevice between the two halves of the roller brush enclosure.

Move the blue fulcrum connecting the bottom and the main body of the vacuum cleaner back and forth to loosen up crevice between the two halves of the roller brush enclosure.

Step 5

• Insert the plastic opening tool into the crevice between the blue and the dark grey plastic frames enclosing the roller brush.
• Apply an outward force throughout and all around the gap in order to separate the two plastic frames.

Insert the plastic opening tool into the crevice between the blue and the dark grey plastic frames enclosing the roller brush.

Apply an outward force throughout and all around the gap in order to separate the two plastic frames.

Step 6

• Lift the grey frame off the bottom of the vacuum cleaner with your hands and place it on a flat surface.

Lift the grey frame off the bottom of the vacuum cleaner with your hands and place it on a flat surface.

Step 7

• Lift the roller brush slightly upwards using your hand.
• Take one side of the black roller brush belt off by pulling it over the end of the roller brush with your other hand.

Lift the roller brush slightly upwards using your hand.

Take one side of the black roller brush belt off by pulling it over the end of the roller brush with your other hand.

Step 8

• Remove the roller brush belt with your hands by sliding it of the end of the motor.

Remove the roller brush belt with your hands by sliding it of the end of the motor.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.                                             

Author

                                      with 5 other contributors 

                    Elena Postupalskaya                     

Member since: 10/02/2017

1,039 Reputation

                                      6 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges                           

Team

                       Cal Poly, Team S15-G2, Livingston Fall 2017                        

                                                  Member of Cal Poly, Team S15-G2, Livingston Fall 2017 



                    CPSU-LIVINGSTON-F17S15G2                     


                                            3 Members                     


                                            14 Guides authored                     

Forrest Sutton - Mar 30, 2019

Reply

Whhhhyyyyyy does this require a special, hard to find bit to disassemble!!!!! I have screw driver set with everything from philips, standard, Allen and even the star bits. But they had to go a use one with a %#*@ peg in the middle rendering all my tools useless. Had I known I would never have bought it.

Ellen Long - Feb 23, 2020

I agree, Yeah why!

Bryan Hawkins - Sep 9, 2020

Reply

Amy Johnson - Dec 20, 2021

Reply

My roller brush is just locked. I have the hair cleaned out but it won’t budge. Is there a release button somewhere?

April McClure - Dec 11, 2022

I need to know the same thing please