Difficulty
Moderate
Steps
15
Time Required
15 - 20 minutes
Sections
3
- Shark Professional Steam Pocket Mop Front Panel Disassembly
- 6 steps
- Shark Professional Steam Pocket Mop Open Mop Body
- 5 steps
- Electric Valve
- 4 steps
Flags
0
BackShark Professional Steam Pocket Mop
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Shark Professional Steam Pocket Mop Front Panel Disassembly
- Unwrap the power cord from the handle.
- Remove the 56.0 mm Phillips head #2 screw located above the water tank cap.
- Pull the handle to separate it from the body.
Unwrap the power cord from the handle.
Remove the 56.0 mm Phillips head #2 screw located above the water tank cap.
Pull the handle to separate it from the body.
1024
Step 2
- Remove the three 12.0 mm Phillips head #2 screws where the handle connects to the body.
- Remove the plastic cap.
Remove the three 12.0 mm Phillips head #2 screws where the handle connects to the body.
Remove the plastic cap.
Step 3
- Remove the three 16.0 mm T10 Torx screws near the top of the body and remove the water tank cap.
- The third screw is directly on other side of the bottom screw in the photo.
Remove the three 16.0 mm T10 Torx screws near the top of the body and remove the water tank cap.
The third screw is directly on other side of the bottom screw in the photo.
Step 4
- Remove steam control button cover with a metal spudger.
- Remove the two 12.0 mm Phillips head #2 screws underneath.
- Remove the plastic rim with clear plastic cover.
Remove steam control button cover with a metal spudger.
Remove the two 12.0 mm Phillips head #2 screws underneath.
Remove the plastic rim with clear plastic cover.
Step 5
- Remove the Shark logo decal on the front of body using a metal spudger.
- Remove the two 12.0 mm Phillips head #2 screws underneath.
- Pull out the plastic cover to remove.
Remove the Shark logo decal on the front of body using a metal spudger.
Pull out the plastic cover to remove.
Step 6
- Pop off the grey front plate to expose the control panel and screws necessary to open mop body.
Pop off the grey front plate to expose the control panel and screws necessary to open mop body.
Step 7
Shark Professional Steam Pocket Mop Open Mop Body
- Remove the three 12.0 mm Philips head #2 screws connected to the dark grey plastic trim.
Remove the three 12.0 mm Philips head #2 screws connected to the dark grey plastic trim.
Step 8
- Remove the four 16.0 mm T10 Torx screws located on the back of the mop.
Remove the four 16.0 mm T10 Torx screws located on the back of the mop.
Step 9
- Remove the two 12.0 mm Phillips head #2 screws that hold the power cord to the device.
Remove the two 12.0 mm Phillips head #2 screws that hold the power cord to the device.
Step 10
- Pop off the dark grey plastic trim cover.
Pop off the dark grey plastic trim cover.
Step 11
- Pop open the white plastic mop body by pulling apart from the front and back side.
Pop open the white plastic mop body by pulling apart from the front and back side.
Step 12
Electric Valve
- Remove the four 12.0 mm Phillips head #2 screws on top of the electric valve.
Remove the four 12.0 mm Phillips head #2 screws on top of the electric valve.
Step 13
- Remove both plastic pieces holding the electric valve in place.
Remove both plastic pieces holding the electric valve in place.
Step 14
- Lift electric valve out of place and tilt to the side to expose and remove the two 12.0 mm Phillips head #2 screws on the side.
Lift electric valve out of place and tilt to the side to expose and remove the two 12.0 mm Phillips head #2 screws on the side.
Step 15
- Pull apart to remove the electronic valve.
Pull apart to remove the electronic valve.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Brett Wilson
Member since: 02/12/2018
926 Reputation
6 Guides authored
Badges:
13
+10 more badges
Team
USF Tampa, Team S15-G1, Boczar Spring 2018
Member of USF Tampa, Team S15-G1, Boczar Spring 2018
USFT-BOCZAR-S18S15G1
4 Members
14 Guides authored
