Shark Professional Steam Pocket Mop Water Tank Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Shark Professional Steam Pocket Mop Front Panel Disassembly
6 steps
Shark Professional Steam Pocket Mop Open Mop Body
5 steps
Water Tank
5 steps

Flags

BackShark Professional Steam Pocket Mop
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Shark Professional Steam Pocket Mop Front Panel Disassembly

Unwrap the power cord from the handle.
Remove the 56.0 mm Phillips head #2 screw located above the water tank cap.
Pull the handle to separate it from the body.

Unwrap the power cord from the handle.

Remove the 56.0 mm Phillips head #2 screw located above the water tank cap.

Pull the handle to separate it from the body.

1024

Step 2

Remove the three 12.0 mm Phillips head #2 screws where the handle connects to the body.
Remove the plastic cap.

Remove the three 12.0 mm Phillips head #2 screws where the handle connects to the body.

Remove the plastic cap.

Step 3

Remove the three 16.0 mm T10 Torx screws near the top of the body and remove the water tank cap.
The third screw is directly on other side of the bottom screw in the photo.

Remove the three 16.0 mm T10 Torx screws near the top of the body and remove the water tank cap.

The third screw is directly on other side of the bottom screw in the photo.

Step 4

Remove steam control button cover with a metal spudger.
Remove the two 12.0 mm Phillips head #2 screws underneath.
Remove the plastic rim with clear plastic cover.

Remove steam control button cover with a metal spudger.

Remove the two 12.0 mm Phillips head #2 screws underneath.

Remove the plastic rim with clear plastic cover.

Step 5

Remove the Shark logo decal on the front of body using a metal spudger.
Remove the two 12.0 mm Phillips head #2 screws underneath.
Pull out the plastic cover to remove.

Remove the Shark logo decal on the front of body using a metal spudger.

Pull out the plastic cover to remove.

Step 6

Pop off the grey front plate to expose the control panel and screws necessary to open mop body.

Pop off the grey front plate to expose the control panel and screws necessary to open mop body.

Step 7

              Shark Professional Steam Pocket Mop Open Mop Body

Remove the three 12.0 mm Philips head #2 screws connected to the dark grey plastic trim.

Remove the three 12.0 mm Philips head #2 screws connected to the dark grey plastic trim.

Step 8

Remove the four 16.0 mm T10 Torx screws located on the back of the mop.

Remove the four 16.0 mm T10 Torx screws located on the back of the mop.

Step 9

Remove the two 12.0 mm Phillips head #2 screws that hold the power cord to the device.

Remove the two 12.0 mm Phillips head #2 screws that hold the power cord to the device.

Step 10

Pop off the dark grey plastic trim cover.

Pop off the dark grey plastic trim cover.

Step 11

Pop open the white plastic mop body by pulling apart from the front and back side.

Pop open the white plastic mop body by pulling apart from the front and back side.

Step 12

              Water Tank

Remove the top left 12.0 mm Phillips head #2 screw from inside body.

Remove the top left 12.0 mm Phillips head #2 screw from inside body.

Step 13

Remove four 12.0 mm Phillips head #2 screws from the inside of the mop body.

Remove four 12.0 mm Phillips head #2 screws from the inside of the mop body.

Step 14

Pull apart the bottom of the mop body from the dark grey connector.
Disconnect the tube from the bottom

Pull apart the bottom of the mop body from the dark grey connector.

Disconnect the tube from the bottom

Step 15

Remove two 12.0 mm Phillips head #2 screws on the top and then pull back the black foam to reveal and remove the third 12.0 mm Phillips head #2 screw.

Remove two 12.0 mm Phillips head #2 screws on the top and then pull back the black foam to reveal and remove the third 12.0 mm Phillips head #2 screw.

Step 16

Pull apart the mop body from the water tank to separate.

Pull apart the mop body from the water tank to separate.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Brett Wilson

Member since: 02/12/2018

926 Reputation

                                      6 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       USF Tampa, Team S15-G1, Boczar Spring 2018                        

                                                  Member of USF Tampa, Team S15-G1, Boczar Spring 2018 



                    USFT-BOCZAR-S18S15G1                     


                                            4 Members                     


                                            14 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team