Difficulty
Moderate
Steps
11
Time Required
15 minutes
Sections
2
- Rotary Brush
- 10 steps
- Rotary Belt
- 1 step
Flags
0
BackShark Rocket HV301
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rotary Brush
- Flip the vacuum so the bottom base is visible.
- Gently pry the bottom two wheels off with a plastic opening tool.
Flip the vacuum so the bottom base is visible.
Gently pry the bottom two wheels off with a plastic opening tool.
1024
Step 2
- Remove five visible screws with a Phillips #2 screwdriver.
- Locate and twist the three plastic screws to the unlock position with a quarter or flathead screwdriver.
Remove five visible screws with a Phillips #2 screwdriver.
Locate and twist the three plastic screws to the unlock position with a quarter or flathead screwdriver.
Step 3
- Remove plate covering the roller brush.
Remove plate covering the roller brush.
Step 4
- Use a Phillips #2 screwdriver to extract the three screws revealed from removing the plate.
Use a Phillips #2 screwdriver to extract the three screws revealed from removing the plate.
Step 5
- Turn the vacuum over so the rotary brush is on the ground.
- Grab the vacuum on both sides of the hose and pull up to remove the top of the vacuum halfway.
Turn the vacuum over so the rotary brush is on the ground.
Grab the vacuum on both sides of the hose and pull up to remove the top of the vacuum halfway.
Step 6
- Gently pinch the head of the cable and pull upwards until the casing disconnects from the vacuum.
- Proceed with removing the upper casing.
Gently pinch the head of the cable and pull upwards until the casing disconnects from the vacuum.
Proceed with removing the upper casing.
Step 7
- Use a Phillips #2 screwdriver to remove the four visible screws securing the rotary brush to the vacuum.
Use a Phillips #2 screwdriver to remove the four visible screws securing the rotary brush to the vacuum.
Step 8
- Remove the rotary belt on right side of vacuum from the bearing.
- Gently lift the casing to remove the belt and brush from the vacuum.
Remove the rotary belt on right side of vacuum from the bearing.
Gently lift the casing to remove the belt and brush from the vacuum.
Step 9
- Gently pry off the plastic casing on both sides of rotary brush.
- Lift the clear plastic shell from the rotary brush.
Gently pry off the plastic casing on both sides of rotary brush.
Lift the clear plastic shell from the rotary brush.
Step 10
- Remove the rotary belt attached to the brush and replace it if needed.
Remove the rotary belt attached to the brush and replace it if needed.
Step 11
Rotary Belt
- Replace belt if torn or damaged.
Replace belt if torn or damaged.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
13 other people completed this guide.
Author
with 7 other contributors
Trey Nahhas
Member since: 10/06/2016
690 Reputation
1 Guide authored
Badges:
16
+13 more badges
Team
Cal Poly, Team 10-5, Livingston Fall 2016
Member of Cal Poly, Team 10-5, Livingston Fall 2016
CPSU-LIVINGSTON-F16S10G5
4 Members
14 Guides authored
oneupchallenges - Sep 25, 2018
Reply
Where can I find the rotary belt for the Shark Duo?
Jennifer Dalton - Feb 8, 2021
Reply
I could not get it out without removing the brush roll motor. So I am putting it back together and I need to know if the motor has a top and bottom. What I mean is does it matter ? Thank you
SYSTEM 855 - Nov 19, 2022
Reply
Thanks for the guide it came in super handy
