Shark Rotator Powered Lift Away Speed Belt Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 2 hours

Sections

Belt
16 steps

Flags

BackShark Rotator Powered Lift-Away Speed
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Belt

Turn the vacuum on its side.
Using a quarter, twist the three green locks to the unlock position.
Pull the bottom roller brush cover to open the vacuum.

Turn the vacuum on its side.

Using a quarter, twist the three green locks to the unlock position.

Pull the bottom roller brush cover to open the vacuum.

1024

Step 2

Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

Step 3

Remove the three 14.3 mm screws with a T20 screwdriver.

Remove the three 14.3 mm screws with a T20 screwdriver.

Step 4

Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

Step 5

Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

Step 6

Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

Step 7

Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

Step 8

Turn the vacuum around.
Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

Turn the vacuum around.

Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

Step 9

Remove both of the headlight covers with the spudger.

Remove both of the headlight covers with the spudger.

Step 10

Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

Step 11

Remove the two 13.4 mm screws with a T20 bit screwdriver.

Remove the two 13.4 mm screws with a T20 bit screwdriver.

Step 12

Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

Step 13

Remove the visible side of the belt from the gear with a spudger.

Remove the visible side of the belt from the gear with a spudger.

Step 14

Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

Step 15

Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

Step 16

Remove the belt from the gear.

Remove the belt from the gear.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Dakota Rodriguez-Ransom

Member since: 10/08/2018

605 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S4-G6, White Fall 2018                        

                                                  Member of Cal Poly, Team S4-G6, White Fall 2018 



                    CPSU-WHITE-F18S4G6                     


                                            4 Members                     


                                            10 Guides authored

Greg Norman - Apr 1, 2021

Where can we buy belts in UK?

Annie Pappineau - 17 hours agoJan 23, 2023

where cn i get a belt for this vaccum

Introduction#

What you need#

Team#

Introduction

What you need

Team