Difficulty
Moderate
Steps
13
Time Required
30 - 45 minutes
Sections
1
- Headlight
- 13 steps
Flags
0
BackShark Rotator Powered Lift-Away Speed
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Headlight
- Flip the vacuum on its underside, and use a coin to rotate the cam-screws on the bottom panel so that their grooves are parallel with the front of the vacuum.
Flip the vacuum on its underside, and use a coin to rotate the cam-screws on the bottom panel so that their grooves are parallel with the front of the vacuum.
1024
Step 2
- Squeeze the sides of the roller brush cover release clasp, and swing the cover open.
Squeeze the sides of the roller brush cover release clasp, and swing the cover open.
Step 3
- Using a T20 screwdriver remove five 15.9 mm screws on the outside of the cover.
Using a T20 screwdriver remove five 15.9 mm screws on the outside of the cover.
Step 4
- Using a T20 screwdriver, remove three 13.4 mm screws from where the roller brush cover attaches to the bottom of the vacuum.
Using a T20 screwdriver, remove three 13.4 mm screws from where the roller brush cover attaches to the bottom of the vacuum.
Step 5
- Using a T20 screwdriver, remove two 13.4 mm screws from under the wheels.
Using a T20 screwdriver, remove two 13.4 mm screws from under the wheels.
Step 6
- Using a T20 screwdriver, remove two 15.9 mm screws behind the vacuum wheels.
Using a T20 screwdriver, remove two 15.9 mm screws behind the vacuum wheels.
Step 7
- Using a PH0 screwdriver bit, remove the single 13.4 mm screw in between the roller brush and where the release clasp was attached.
Using a PH0 screwdriver bit, remove the single 13.4 mm screw in between the roller brush and where the release clasp was attached.
Step 8
- Using a T20 screwdriver, remove the single 13.4 mm screw from behind the belted end of the roller brush.
Using a T20 screwdriver, remove the single 13.4 mm screw from behind the belted end of the roller brush.
Step 9
- Flip the vacuum into the upright position, and use a spudger to open the front assembly cover by prying the seam where the colored front assembly and the grey side covers meet.
Flip the vacuum into the upright position, and use a spudger to open the front assembly cover by prying the seam where the colored front assembly and the grey side covers meet.
Step 10
- Separate the front assembly cover from the vacuum.
Separate the front assembly cover from the vacuum.
Step 11
- Use a spudger to remove the headlight covers by prying the seams where the headlight covers meet the bottom front of the vacuum.
Use a spudger to remove the headlight covers by prying the seams where the headlight covers meet the bottom front of the vacuum.
Step 12
- Pull the LED headlight strand up and away from where it is attached to the bottom front of the vacuum.
Pull the LED headlight strand up and away from where it is attached to the bottom front of the vacuum.
Step 13
- Pinch the tabs on the circuit board clasp for the LED headlight inwards , and pull the clasp up and away to detach the headlight.
Pinch the tabs on the circuit board clasp for the LED headlight inwards , and pull the clasp up and away to detach the headlight.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Dakota Rodriguez-Ransom
Member since: 10/08/2018
605 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team S4-G6, White Fall 2018
Member of Cal Poly, Team S4-G6, White Fall 2018
CPSU-WHITE-F18S4G6
4 Members
10 Guides authored
