Difficulty
Moderate
Steps
12
Time Required
30 minutes
Sections
2
- Roller Brush
- 10 steps
- Roller Brush Belt
- 2 steps
Flags
0
BackShark Rotator Slim-Light Lift-Away Upright
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Roller Brush
- Push the red Lift Away button down and lift up on the vacuum handle to detach the base.
- The handle was removed for convenience but is not required.
Push the red Lift Away button down and lift up on the vacuum handle to detach the base.
The handle was removed for convenience but is not required.
1024
Step 2
- Turn over the vacuum to reveal the roller brush.
Turn over the vacuum to reveal the roller brush.
Step 3
- Pry the small wheels at the bottom of the base using the plastic opening tool.
Pry the small wheels at the bottom of the base using the plastic opening tool.
Step 4
- Using a coin, turn the big white knobs located above the roller brush counter-clockwise.
Using a coin, turn the big white knobs located above the roller brush counter-clockwise.
Step 5
- Lift up the suction hose to reveal a screw.
- Remove the 12.7 mm Phillips #02 screw.
Lift up the suction hose to reveal a screw.
Remove the 12.7 mm Phillips #02 screw.
Step 6
- Remove eight 12.7mm screws located under the vacuum using a Phillips #02 screwdriver.
- Remove two 12.7 mm screws located next to the wheels with a Phillips #02 screwdriver.
- The two screws located next to the wheels are smaller in diameter.
Remove eight 12.7mm screws located under the vacuum using a Phillips #02 screwdriver.
Remove two 12.7 mm screws located next to the wheels with a Phillips #02 screwdriver.
The two screws located next to the wheels are smaller in diameter.
Step 7
- Turn the vacuum upright and pull the white upper section of the brush roller circuit housing.
- Be careful when lifting the housing as there is a connector attached.
Turn the vacuum upright and pull the white upper section of the brush roller circuit housing.
Be careful when lifting the housing as there is a connector attached.
Step 8
- Remove the connector attached to the circuit boards using a plastic opening tool.
Remove the connector attached to the circuit boards using a plastic opening tool.
Step 9
- Remove the two 12.7 mm screws located at the top of the clear plastic brush roller housing using a Phillips #02 screwdriver.
- Lift the clear plastic brush roller housing.
Remove the two 12.7 mm screws located at the top of the clear plastic brush roller housing using a Phillips #02 screwdriver.
Lift the clear plastic brush roller housing.
Step 10
- Wiggle the brush roller upwards from the left and right side slots.
Wiggle the brush roller upwards from the left and right side slots.
Step 11
Roller Brush Belt
- Remove the roller brush by sliding it out toward the left, off the belt.
Remove the roller brush by sliding it out toward the left, off the belt.
Step 12
- Remove the belt from the motor gear by sliding the belt away from the gear and belt motor.
- In the following picture the belt was already removed.
Remove the belt from the motor gear by sliding the belt away from the gear and belt motor.
In the following picture the belt was already removed.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Daniel Ceja
Member since: 01/24/2019
277 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
Cal Poly, Team S19-G3, White Winter 2019
Member of Cal Poly, Team S19-G3, White Winter 2019
CPSU-WHITE-W19S19G3
5 Members
12 Guides authored
