Difficulty

Difficult

Steps

13

Time Required

                          15 - 35 minutes

Sections

4

  • Back Panel
  • 1 step
  • USB Port
  • 5 steps
  • Motherboard
  • 5 steps
  • Battery
  • 2 steps

Flags

0

  • BackSharp Aquos

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

This guide will show you how to open your device and remove the inside motherboard to replace your battery.

What you need

Step 1

              Back Panel
  • Peel back the back cover of the phone from the access point to remove it. It should come off easily using your hands.

Peel back the back cover of the phone from the access point to remove it. It should come off easily using your hands.

1024

Step 2

              USB Port
  • Remove seven 3mm Star #5 screws shown in the picture with a screwdriver.
  • Remove two 3.5mm Star #5 screws shown in the picture with a screwdriver.
  • Remove two 5mm Star #5 screws shown in the picture with a screwdriver.

Remove seven 3mm Star #5 screws shown in the picture with a screwdriver.

Remove two 3.5mm Star #5 screws shown in the picture with a screwdriver.

Remove two 5mm Star #5 screws shown in the picture with a screwdriver.

Step 3

  • Pry open the back panel using a plastic opening tool. Do this around the edges until you are able to lift it off.

Pry open the back panel using a plastic opening tool. Do this around the edges until you are able to lift it off.

Step 4

  • Disconnect the wire by lifting it up with a plastic opening tool.

Disconnect the wire by lifting it up with a plastic opening tool.

Step 5

  • To disconnect the cable, use the tip of a spudger or your fingernail to flip up the small retaining flap. Then, you can safely pull the ribbon cable out.

To disconnect the cable, use the tip of a spudger or your fingernail to flip up the small retaining flap. Then, you can safely pull the ribbon cable out.

Step 6

  • After removing the wires, carefully snap out the usb port with your hands. It is held down by some plastic clips, so some force may be needed.

After removing the wires, carefully snap out the usb port with your hands. It is held down by some plastic clips, so some force may be needed.

Step 7

              Motherboard
  • Peel off the black pieces of tape.

Peel off the black pieces of tape.

Step 8

  • Use the tip of a spudger or your fingernail to flip up the small retaining flap. Then pull the cable out using tweezers.

Use the tip of a spudger or your fingernail to flip up the small retaining flap. Then pull the cable out using tweezers.

Step 9

  • Remove the wire from the two marked connections using tweezers to pull the wire apart from the device.

Remove the wire from the two marked connections using tweezers to pull the wire apart from the device.

Step 10

  • Peel the tape off with your hands.

Peel the tape off with your hands.

Step 11

  • Lift the motherboard out with your hands.

Lift the motherboard out with your hands.

Step 12

              Battery
  • Peel off the tape holding the battery down.

Peel off the tape holding the battery down.

Step 13

  • Lift the battery out with your hands.

Lift the battery out with your hands.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 3 other contributors 


                    Felicia Imbriano

Member since: 03/08/2016

1,169 Reputation

                                      8 Guides authored                  



                       Badges:
                       24







                                                        +21 more badges

Team

                       UMass Dartmouth, Team 7-4, Catania Spring 2016                        

                                                  Member of UMass Dartmouth, Team 7-4, Catania Spring 2016 



                    UMASSD-CATANIA-S16S7G4                     


                                            3 Members                     


                                            24 Guides authored

jeanpaolo lin - Aug 4, 2019

Reply

very helpful. I already replace my sharp 305sh battery

and then I find my power button is out of order.

so i just can keep it still on. use shake to lock screen and touch to unlock.

restart by unplug sim card.

but these day I made it out of power.so it turn off. however I use anyway to make it alive but I can’t.

luck me. I HARDLY PRESS camera left side near down the power button side and press on button .

It turns on.

the power board need to touch on some device on anther side.

!Mucho Gracias!

ari leon Kolbar - Jan 14, 2021

Reply

hello, where can I buy this battery ? thanks, Ari

Masood Ali - May 27, 2022

Reply

battery connector located on motherbaoard has been broken when i was changing my aquos R2 battery…..kind guide me what to do now…..should we use jumper wires direct to the battery ??? if yes then guide me