Difficulty

Moderate

Steps

14

Time Required

Suggest a time??

Sections

6

  • Stand
  • 2 steps
  • Back Case
  • 3 steps
  • Motherboard
  • 4 steps
  • Power Button
  • 1 step
  • Top Buttons
  • 1 step
  • Front Case
  • 3 steps

Flags

0

  • BackSharp Aquos LC13B2UA

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Stand
  • Place the TV face down on a flat smooth surface as to not scratch the screen.
  • Using a Phillips #2 screwdriver remove the four 8mm screws attaching the stand to the TV.

Place the TV face down on a flat smooth surface as to not scratch the screen.

Using a Phillips #2 screwdriver remove the four 8mm screws attaching the stand to the TV.

1024

Step 2

  • Lift the stand off the television.

Lift the stand off the television.

Step 3

              Back Case
  • Remove the two back panels by prying them out with your hands.

Remove the two back panels by prying them out with your hands.

Step 4

  • Using a Phillips #2 screwdriver, remove the eight 6mm Phillips screws located around the edge.
  • Using a Phillips #2 screwdriver, remove the two 6mm Phillips screws located near the inputs.

Using a Phillips #2 screwdriver, remove the eight 6mm Phillips screws located around the edge.

Using a Phillips #2 screwdriver, remove the two 6mm Phillips screws located near the inputs.

Step 5

  • Using your hands, gently lift and remove the back case of the television.

Using your hands, gently lift and remove the back case of the television.

Step 6

              Motherboard
  • Remove the two speaker cables and the connector from the circuit board by pinching the plastic connectors and firmly pulling up.
  • Pull on the plastic part of the connector, even though it may seem easiest to pull on the wires.

Remove the two speaker cables and the connector from the circuit board by pinching the plastic connectors and firmly pulling up.

Pull on the plastic part of the connector, even though it may seem easiest to pull on the wires.

Step 7

  • Remove the green and gray power connector from the side of the buttons panel at the top of the television.
  • Remove the green/gray to orange/gray connector from the center of the circuit board.

Remove the green and gray power connector from the side of the buttons panel at the top of the television.

Remove the green/gray to orange/gray connector from the center of the circuit board.

Step 8

  • Remove the four 5mm phillips screws attaching the LCD and circuit board to the front case.

Remove the four 5mm phillips screws attaching the LCD and circuit board to the front case.

Step 9

  • Lift the circuit board/LCD block from the case by lifting the near side of the circuit board and sliding it under the button frame.

Lift the circuit board/LCD block from the case by lifting the near side of the circuit board and sliding it under the button frame.

Step 10

              Power Button
  • Remove the two 6mm Phillips screws.
  • Pull the board toward you, giving you access to the power button.

Remove the two 6mm Phillips screws.

Pull the board toward you, giving you access to the power button.

Step 11

              Top Buttons
  • Unscrew the two 4mm Phillips screws.
  • Lift the buttons off the front case.

Unscrew the two 4mm Phillips screws.

Lift the buttons off the front case.

Step 12

              Front Case
  • Remove the eight 10mm screws connecting the two speakers to the front case.

Remove the eight 10mm screws connecting the two speakers to the front case.

Step 13

  • Remove the two black tape strips securing the audio cables to the case.
  • Lift the audio cable from the plastic prongs securing it to the front case
  • The speakers can now be removed.

Remove the two black tape strips securing the audio cables to the case.

Lift the audio cable from the plastic prongs securing it to the front case

The speakers can now be removed.

Step 14

  • To remove the LED circuit at the base of the front casing, unscrew the two 5mm Phillips screws.
  • Lift the circuit to remove the plastic LED casing.

To remove the LED circuit at the base of the front casing, unscrew the two 5mm Phillips screws.

Lift the circuit to remove the plastic LED casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Robert Hobson

Member since: 01/20/2011

1,275 Reputation

                                      9 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team 1-11, Amido Winter 2011                        

                                                  Member of Cal Poly, Team 1-11, Amido Winter 2011 



                    CPSU-AMIDO-W11S1G11                     


                                            4 Members                     


                                            9 Guides authored