Difficulty

Difficult

Steps

7

Time Required

                          25 - 30 minutes

Sections

3

  • Outer Case
  • 3 steps
  • Speakers
  • 2 steps
  • LED Lights
  • 2 steps

Flags

1

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

  • BackSharper Image iPulse SI325

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Outer Case
  • Gently position the device so that the buttons and speakers lie face down.
  • Unplug the power cord from the “DC Input.”

Gently position the device so that the buttons and speakers lie face down.

Unplug the power cord from the “DC Input.”

1024

Step 2

  • Remove the four 12mm phillips head #2 screws located along the outer edge of the white case.
  • Be careful! There are two small, easily-broken, plastic tabs at the bottom of the device keeping it together.
  • Once you remove the screws, pick the device up so that the grey label on the bottom of the device faces toward you.
  • With your thumbs on either side of the grey label, slowly push with both thumbs until the case pops open.
  • A small gap will open as the two tabs are released.
  • Do not pull the two halves apart yet. They are held together by the speaker wire.

Remove the four 12mm phillips head #2 screws located along the outer edge of the white case.

Be careful! There are two small, easily-broken, plastic tabs at the bottom of the device keeping it together.

Once you remove the screws, pick the device up so that the grey label on the bottom of the device faces toward you.

With your thumbs on either side of the grey label, slowly push with both thumbs until the case pops open.

A small gap will open as the two tabs are released.

Do not pull the two halves apart yet. They are held together by the speaker wire.

Step 3

  • Grip both sides of the top round part of the case and carefully open it like a clam. The bottom of the two halves are connected by the speaker wire. Do not separate by more than 1 centimeter.
  • Grip either side of the top round part of the case and carefully open the device to reveal all the hidden treasures inside!
  • Lay the device down, so that all the internal components are facing upwards.

Grip both sides of the top round part of the case and carefully open it like a clam. The bottom of the two halves are connected by the speaker wire. Do not separate by more than 1 centimeter.

Grip either side of the top round part of the case and carefully open the device to reveal all the hidden treasures inside!

Lay the device down, so that all the internal components are facing upwards.

Step 4

              Speakers
  • Disconnect the speaker wire from the motherboard by firmly griping the black and red wires close to the connection with two fingers and pulling the connector out.
  • Wiggling the connector back and forth as you pull will make removal easier.

Disconnect the speaker wire from the motherboard by firmly griping the black and red wires close to the connection with two fingers and pulling the connector out.

Wiggling the connector back and forth as you pull will make removal easier.

Step 5

  • Remove the eight 11mm Phillips #1 screws that connect the speakers to the white outer case.

Remove the eight 11mm Phillips #1 screws that connect the speakers to the white outer case.

Step 6

              LED Lights
  • Remove the four 7mm Phillips #1 screws on the circuit board with the LED lights.
  • Slowly lift the circuit board out of the front cover and place the cover out of the way.

Remove the four 7mm Phillips #1 screws on the circuit board with the LED lights.

Slowly lift the circuit board out of the front cover and place the cover out of the way.

Step 7

  • Remove the solder connecting the LED light that needs replacement.

Remove the solder connecting the LED light that needs replacement.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Melissa Pasa

Member since: 10/13/2013

701 Reputation

                                      7 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Cal Poly, Team 11-33, Amido Fall 2013                        

                                                  Member of Cal Poly, Team 11-33, Amido Fall 2013 



                    CPSU-AMIDO-F13S11G33                     


                                            4 Members                     


                                            8 Guides authored