Difficulty
Moderate
Steps
12
Time Required
6 minutes
Sections
2
- Sharper Image SVC430 Disassembly
- 10 steps
- Tripod Nut
- 2 steps
Flags
0
BackSharper Image SVC430
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
- Remove the device from the caseCompletely tear down the deviceLocate the tripod nut Remove the tripod nut
What you need
Step 1
Sharper Image SVC430 Disassembly
- Power off your device before you begin.
- Use your thumb to push down on the lever that says “open” while simultaneously pushing up the latch with your other thumb.
Power off your device before you begin.
Use your thumb to push down on the lever that says “open” while simultaneously pushing up the latch with your other thumb.
1024
Step 2
- Once the latch is free, simply pull the front of the waterproof case off and slide the camera out.
Once the latch is free, simply pull the front of the waterproof case off and slide the camera out.
Step 3
- Locate the bottom of the device.
- Now, using the metal screwdriver, unscrew the screw on the bottom of the device.
Locate the bottom of the device.
Now, using the metal screwdriver, unscrew the screw on the bottom of the device.
Step 4
- This panel should come off easily, do not apply too much pressure.
- Use the plastic opening tool to pry open the plastic panel from the top of the camera.
- Locate the two screws on the top of the device.
This panel should come off easily, do not apply too much pressure.
Use the plastic opening tool to pry open the plastic panel from the top of the camera.
Locate the two screws on the top of the device.
Step 5
- Use the JIS J0 screwdriver to unscrew the two screws on the top of the device.
Use the JIS J0 screwdriver to unscrew the two screws on the top of the device.
Step 6
- Use the plastic opening tool to pry off the back panel.
- The back panel will come off easily.
Use the plastic opening tool to pry off the back panel.
The back panel will come off easily.
Step 7
- Use the metal screwdriver to unscrew the screw from the back of the device.
Use the metal screwdriver to unscrew the screw from the back of the device.
Step 8
- Use the plastic opening tool to pry off the front panel of the device.
Use the plastic opening tool to pry off the front panel of the device.
Step 9
- Using the screwdriver, unscrew the screw located underneath the front panel.
Using the screwdriver, unscrew the screw located underneath the front panel.
Step 10
- Be gentle with the device since there are wires attached to the front plate and two halves.
- Gently pull both sides of the device to expose the interior of the device.
Be gentle with the device since there are wires attached to the front plate and two halves.
Gently pull both sides of the device to expose the interior of the device.
Step 11
Tripod Nut
- Locate the two screws that attach the tripod nut to the device.
Locate the two screws that attach the tripod nut to the device.
Step 12
- Unscrew the two screws located on the back of the half that the tripod nut is located.
- Once the screws are removed, the tripod nut can easily be removed.
Unscrew the two screws located on the back of the half that the tripod nut is located.
Once the screws are removed, the tripod nut can easily be removed.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Kathryn Mattingly
Member since: 01/29/2016
698 Reputation
6 Guides authored
Badges:
10
+7 more badges
Team
University of Kentucky Louisville, Team 1-6, Matravers Spring 2016
Member of University of Kentucky Louisville, Team 1-6, Matravers Spring 2016
LOUISVILLE-MATRAVERS-S16S1G6
4 Members
6 Guides authored
