Difficulty

Moderate

Steps

11

Time Required

                          20 minutes

Sections

3

  • Power Unit Assembly
  • 4 steps
  • Power Cable
  • 4 steps
  • Motor
  • 3 steps

Flags

0

  • BackShop-Vac MC150A

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Unlatch the power unit assembly
  • Before you begin, make sure to switch off the device and unplug it from the outlet.
  • Unlatch the two side clips securing the power unit assembly to the tank.
  • Remove the power unit assembly from the tank assembly.

Before you begin, make sure to switch off the device and unplug it from the outlet.

Unlatch the two side clips securing the power unit assembly to the tank.

Remove the power unit assembly from the tank assembly.

1024

Step 2

              Remove the top cover
  • Use a 3.5 mm hex key to remove the three screws securing the top cover.
  • Remove the top cover.

Use a 3.5 mm hex key to remove the three screws securing the top cover.

Remove the top cover.

Step 3

  • Use a 3.5 mm hex key to remove the four screws securing the power unit assembly.

Use a 3.5 mm hex key to remove the four screws securing the power unit assembly.

Step 4

  • Separate the power unit assembly from the cover.

Separate the power unit assembly from the cover.

Step 5

              Disconnect the switch
  • Pull out and disconnect the four spade connectors from the switch module.
  • During reassembly, use the last image as a reference for how to connect the wires.

Pull out and disconnect the four spade connectors from the switch module.

During reassembly, use the last image as a reference for how to connect the wires.

Step 6

              Unscrew the motor bracket
  • Use a Torx T15 driver to unscrew the two screws securing the metal motor bracket.

Use a Torx T15 driver to unscrew the two screws securing the metal motor bracket.

Step 7

  • During reassembly, be sure to reattach the green ground wire clip to the bracket.

During reassembly, be sure to reattach the green ground wire clip to the bracket.

Step 8

  • Separate the clip from the green wire and transfer it to the replacement motor.

Separate the clip from the green wire and transfer it to the replacement motor.

Step 9

              Motor
  • Remove the motor bracket.

Remove the motor bracket.

Step 10

  • Turn the part over to the other side.
  • Use the socket wrench remove the bolt securing the aluminum plate.

Turn the part over to the other side.

Use the socket wrench remove the bolt securing the aluminum plate.

Step 11

  • Unscrew the two Phillips head screws holding the cover to the motor.
  • After removing the cover to the motor, you can replace the motor.

Unscrew the two Phillips head screws holding the cover to the motor.

After removing the cover to the motor, you can replace the motor.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 5 other contributors 


                    Ngunlian

Member since: 02/08/2016

700 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       IUPUI, Team 1-2, Baechle Spring 2016                        

                                                  Member of IUPUI, Team 1-2, Baechle Spring 2016 



                    IUPUI-BAECHLE-S16S1G2                     


                                            5 Members                     


                                            10 Guides authored

Gerald Mikel - Jan 10, 2023

Reply

Where do I buy a new motor?????