Difficulty

Moderate

Steps

7

Time Required

Suggest a time??

Sections

2

  • Opening the Siemens Surpresso Compact
  • 6 steps
  • Water tank seal
  • 1 step

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSiemens Surpresso Compact TK52001

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Opening the Siemens Surpresso Compact
  • Unplug your coffee maker!
  • Remove the water container, the brew group and the drip tray with pomace container.
  • Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.
  • Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

Unplug your coffee maker!

Remove the water container, the brew group and the drip tray with pomace container.

Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.

Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

1024

Step 2

  • Remove the two Torx T10 screws on the top.

Remove the two Torx T10 screws on the top.

Step 3

  • Remove seven T10 Torx screws on the back.
  • The two screws at the bottom of the front can remain.

Remove seven T10 Torx screws on the back.

The two screws at the bottom of the front can remain.

Step 4

  • Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.
  • Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.
  • Lift the top off.
  • On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.

Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.

Lift the top off.

On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

Step 5

  • Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.
  • Remove the two tabs from the power switch.
  • Take off the side panel with the brew group.

Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.

Remove the two tabs from the power switch.

Take off the side panel with the brew group.

Step 6

  • Do the same with the panel on the other side.
  • To remove the water tank hose simply pull it of the pump.
  • Remove the side panel.

Do the same with the panel on the other side.

To remove the water tank hose simply pull it of the pump.

Remove the side panel.

Step 7

              Water tank seal
  • Turn the coffee maker so the side panel faces you.
  • Press the two plastic expansion rivets together with pliers and push them out.
  • Turn the side panel over again
  • Lift the cap over the gasket.
  • Remove the seal.

Turn the coffee maker so the side panel faces you.

Press the two plastic expansion rivets together with pliers and push them out.

Turn the side panel over again

Lift the cap over the gasket.

Remove the seal.

To reassemble your device, follow the steps in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             


        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

[deleted]

VauWeh

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges

Kjetil Solvang Carlsen - Nov 25, 2020

Reply

Where can I find a part-list for the seals etc? I am worried im am missing a seal. I also saw a video of usage of food grade grease I am willing to try.

VauWeh - Nov 25, 2020

In germany for example https://www.juraprofi.de/ or www.komtra.de. Ask them, if they ship to your country.