Difficulty

Moderate

Steps

9

Time Required

Suggest a time??

Sections

2

  • Opening the Siemens Surpresso Compact
  • 6 steps
  • Gear Drive
  • 3 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSiemens Surpresso Compact TK52001

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Opening the Siemens Surpresso Compact
  • Unplug your coffee maker!
  • Remove the water container, the brew group and the drip tray with pomace container.
  • Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.
  • Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

Unplug your coffee maker!

Remove the water container, the brew group and the drip tray with pomace container.

Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.

Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

1024

Step 2

  • Remove the two Torx T10 screws on the top.

Remove the two Torx T10 screws on the top.

Step 3

  • Remove seven T10 Torx screws on the back.
  • The two screws at the bottom of the front can remain.

Remove seven T10 Torx screws on the back.

The two screws at the bottom of the front can remain.

Step 4

  • Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.
  • Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.
  • Lift the top off.
  • On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.

Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.

Lift the top off.

On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

Step 5

  • Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.
  • Remove the two tabs from the power switch.
  • Take off the side panel with the brew group.

Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.

Remove the two tabs from the power switch.

Take off the side panel with the brew group.

Step 6

  • Do the same with the panel on the other side.
  • To remove the water tank hose simply pull it of the pump.
  • Remove the side panel.

Do the same with the panel on the other side.

To remove the water tank hose simply pull it of the pump.

Remove the side panel.

Step 7

              Gear Drive
  • Rotate clockwise the expansion box about 60 degrees and pull it out.
  • The expansion box is frequently filled with coffee oils or grounds. Clean it from time to time. It can easily be separated into two halves.

Rotate clockwise the expansion box about 60 degrees and pull it out.

The expansion box is frequently filled with coffee oils or grounds. Clean it from time to time. It can easily be separated into two halves.

Step 8

  • The drainage valve is directly plugged to the gear drive. The drive is fixed with five Torx T10 screws on the center panel behind the brew group.
  • Remove the five Torx T10 screws holding the gear drive in place.

The drainage valve is directly plugged to the gear drive. The drive is fixed with five Torx T10 screws on the center panel behind the brew group.

Remove the five Torx T10 screws holding the gear drive in place.

Step 9

  • Push the gear drive outwards to the left. Pay attention, several cables might get caught.
  • Lay the gear drive on its side. Loosen the upper water connector by pulling the clamp and than sliding off the hose. Mind the O-ring on the end of the hose, replace it if necessary.

Push the gear drive outwards to the left. Pay attention, several cables might get caught.

Lay the gear drive on its side. Loosen the upper water connector by pulling the clamp and than sliding off the hose. Mind the O-ring on the end of the hose, replace it if necessary.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             


        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

jana°

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges

Soren - Oct 21, 2019

Reply

My replacement valve (original Bosch part) didn’t fit correctly - after it was mounted, the light plastic part couldn’t be moved forth and back without getting stuck from time to time, so the machine wouldn’t be able to brew any coffee afterwards. I fixed it by reusing the light plastic part from the old valve. The machine works perfect now!