Siemens Surpresso Open Bosch Benvenuto Repair Guide

Difficulty

Moderate

Steps

6

Time Required

Suggest a time??

Sections

5

• Siemens Surpresso - Bosch Benvenuto Brew Group Removal
• 2 steps
• Siemens Surpresso - Bosch Benvenuto back panel removal
• 1 step
• Siemens Surpresso - Bosch Benvenuto top cover removal
• 1 step
• Siemens Surpresso - Bosch Benvenuto remove left side panel
• 1 step
• Siemens Surpresso - Bosch Benvenuto remove right side panel
• 1 step

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackSiemens Surpresso - Bosch Benvenuto

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Siemens Surpresso - Bosch Benvenuto Brew Group Removal               

• Never forget: Pull the power plug!
• Remove all attachments such as water reservoir, coffee compartment lid, trester drawer.
• Remove all coffee beans from the bean hopper.
• Open the side flap.

Never forget: Pull the power plug!

Remove all attachments such as water reservoir, coffee compartment lid, trester drawer.

Remove all coffee beans from the bean hopper.

Open the side flap.

1024

Step 2

• Loosen the three rubber caps on the brew group.
• Using a strong flat-blade screwdriver, adjust the three plastic slots underneath so that the “unlocked” position is indicated.
• Note: with the newer version of the brew group, only one lever needs to be flipped.
• Pull out the brew group. If it is stuck, pull firmly and evenly, but with feeling, preferably at the bottom right.

Loosen the three rubber caps on the brew group.

Using a strong flat-blade screwdriver, adjust the three plastic slots underneath so that the “unlocked” position is indicated.

Note: with the newer version of the brew group, only one lever needs to be flipped.

Pull out the brew group. If it is stuck, pull firmly and evenly, but with feeling, preferably at the bottom right.

Step 3

              Siemens Surpresso - Bosch Benvenuto back panel removal               

• Remove the seven Torx T10 screws on the rear panel.
• Do not remove the back panel completely yet, the power switch is still connected.
• Lift the back panel away.
• Remove the two flat plugs from the inside of the power switch.

Remove the seven Torx T10 screws on the rear panel.

Do not remove the back panel completely yet, the power switch is still connected.

Lift the back panel away.

Remove the two flat plugs from the inside of the power switch.

Step 4

              Siemens Surpresso - Bosch Benvenuto top cover removal               

• The top cover is engaged with bayonets in several places. It must first be pushed back about 1 cm and then lifted away upwards.
• Grasp the powder compartment cover firmly and pull it upwards out of its hinges. Otherwise it will be in the way of the top cover.
• Pull the top cover back about 1 cm. If it sticks in front, you can help a little with plastic levers.
• Lift the top cover away from the top.

The top cover is engaged with bayonets in several places. It must first be pushed back about 1 cm and then lifted away upwards.

Grasp the powder compartment cover firmly and pull it upwards out of its hinges. Otherwise it will be in the way of the top cover.

Pull the top cover back about 1 cm. If it sticks in front, you can help a little with plastic levers.

Lift the top cover away from the top.

Step 5

              Siemens Surpresso - Bosch Benvenuto remove left side panel               

• The side panel is attached to the front edge with three bayonets. It must therefore be lifted out upward.
• Grasp the side panel firmly at the rear edge and pull it backward and upward at the same time. It should come off quite easily.
• When reassembling, make sure that the bayonets on the front edge engage properly.

The side panel is attached to the front edge with three bayonets. It must therefore be lifted out upward.

Grasp the side panel firmly at the rear edge and pull it backward and upward at the same time. It should come off quite easily.

When reassembling, make sure that the bayonets on the front edge engage properly.

Step 6

              Siemens Surpresso - Bosch Benvenuto remove right side panel               

Follow the steps in reverse order to reassemble your device

Cancel: I did not complete this guide.

        oldturkey03 is helping us fix the world!      Want to contribute?      Start translating › 

Special thanks to these translators:

100%

oldturkey03

Author

                                      with 1 other contributor 

                    VauWeh                     

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges