Difficulty

Moderate

Steps

9

Time Required

Suggest a time??

Sections

2

  • Opening the Siemens Surpresso Compact
  • 6 steps
  • Coffee Spout distributor
  • 3 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSiemens Surpresso TK56001

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Note: the opening of the device is shown on a Surpresso Compact, but it is basically the same. Pay attention to any cables to the sensors.

What you need

Step 1

              Opening the Siemens Surpresso Compact
  • Unplug your coffee maker!
  • Remove the water container, the brew group and the drip tray with pomace container.
  • Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.
  • Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

Unplug your coffee maker!

Remove the water container, the brew group and the drip tray with pomace container.

Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.

Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

1024

Step 2

  • Remove the two Torx T10 screws on the top.

Remove the two Torx T10 screws on the top.

Step 3

  • Remove seven T10 Torx screws on the back.
  • The two screws at the bottom of the front can remain.

Remove seven T10 Torx screws on the back.

The two screws at the bottom of the front can remain.

Step 4

  • Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.
  • Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.
  • Lift the top off.
  • On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.

Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.

Lift the top off.

On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

Step 5

  • Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.
  • Remove the two tabs from the power switch.
  • Take off the side panel with the brew group.

Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.

Remove the two tabs from the power switch.

Take off the side panel with the brew group.

Step 6

  • Do the same with the panel on the other side.
  • To remove the water tank hose simply pull it of the pump.
  • Remove the side panel.

Do the same with the panel on the other side.

To remove the water tank hose simply pull it of the pump.

Remove the side panel.

Step 7

              Coffee Spout distributor
  • The semicircular decorative strip around the panel above the coffee spout is held from the inside on the left and right by two small white plastic wedges. Use your fingers to pull them out.

The semicircular decorative strip around the panel above the coffee spout is held from the inside on the left and right by two small white plastic wedges. Use your fingers to pull them out.

Step 8

  • The panel with the logo is held by the decorative strip. The decorative strip can now be pulled forward a little at the bottom, then the panel will come off easily
  • The decorative strip does not necessarily have to be completely removed.

The panel with the logo is held by the decorative strip. The decorative strip can now be pulled forward a little at the bottom, then the panel will come off easily

The decorative strip does not necessarily have to be completely removed.

Step 9

  • The housing around the coffee spout distributor consists of two halves. The front part is locked on the left and right.
  • Insert a plastic opening tool into the gap on the side and separate the two halves of the case. The clips are pretty tight.
  • Remove the two Torx T10 screws on the coffee spout distributor.
  • Disconnect the silicone tube at the top of the coffee spout distributor. Pay attention to the wire spiral.
  • Remove the coffee spout distributor.

The housing around the coffee spout distributor consists of two halves. The front part is locked on the left and right.

Insert a plastic opening tool into the gap on the side and separate the two halves of the case. The clips are pretty tight.

Remove the two Torx T10 screws on the coffee spout distributor.

Disconnect the silicone tube at the top of the coffee spout distributor. Pay attention to the wire spiral.

Remove the coffee spout distributor.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             


        VauWeh is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges