Difficulty
Moderate
Steps
14
Time Required
Suggest a time??
Sections
6
- Battery
- 2 steps
- Handle
- 1 step
- Quick Reference Gauge
- 1 step
- Chuck Sleeve
- 2 steps
- Adjustable Clutch
- 2 steps
- Trigger
- 6 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackSkil X-Drive 18V Cordless Drill Model No. 2887
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Un-clip Battery
- Grip the drill. Locate the red locking switch on the back of the battery. Hold the switch down.
Grip the drill. Locate the red locking switch on the back of the battery. Hold the switch down.
1024
Step 2
Remove Battery
- While holding down the red locking switch, slide the battery towards the back of the drill until the battery is fully removed from the drill.
While holding down the red locking switch, slide the battery towards the back of the drill until the battery is fully removed from the drill.
Step 3
Remove Handle
- Grip cordless drill firmly with left hand. Grip the cordless drill handle firmly with the right hand. Rotate the handle counterclockwise in order to remove the handle from the drill.
Grip cordless drill firmly with left hand. Grip the cordless drill handle firmly with the right hand. Rotate the handle counterclockwise in order to remove the handle from the drill.
Step 4
Remove Gauge
- Hold drill upright with one hand and slide the gauge backwards to remove it with the other.
Hold drill upright with one hand and slide the gauge backwards to remove it with the other.
Step 5
Remove the screw from the chuck sleeve
- The chuck sleeve is held on by a 20mm Phillips #2 screw in the center.This screw is reverse threaded. Insert a Phillips #2 screwdriver and rotate it clockwise to loosen and remove it.
The chuck sleeve is held on by a 20mm Phillips #2 screw in the center.This screw is reverse threaded. Insert a Phillips #2 screwdriver and rotate it clockwise to loosen and remove it.
Step 6
Remove the chuck sleeve
- The threaded hole the screw was in is in the shape of a 6-point star. Insert a T40 Torx Key and rotate it clockwise to loosen and remove the chuck sleeve.
The threaded hole the screw was in is in the shape of a 6-point star. Insert a T40 Torx Key and rotate it clockwise to loosen and remove the chuck sleeve.
Step 7
Remove the screws from the adjustable clutch
- Set the adjustable clutch to the “1” setting before beginning. This will make it easier to remove.
- The adjustable clutch is held on by 2 20mm T10 Torx screws. Insert a T10 Torx screwdriver and rotate it counterclockwise to loosen and remove each screw.
Set the adjustable clutch to the “1” setting before beginning. This will make it easier to remove.
The adjustable clutch is held on by 2 20mm T10 Torx screws. Insert a T10 Torx screwdriver and rotate it counterclockwise to loosen and remove each screw.
Step 8
Remove the adjustable clutch
- Firmly grip the outside of the adjustable clutch and pull it off.
- There is a metal washer behind the adjustable clutch that holds in 12 small ball bearings. Hold the drill so it is pointing up slightly so the washer and bearings do not fall out.
Firmly grip the outside of the adjustable clutch and pull it off.
There is a metal washer behind the adjustable clutch that holds in 12 small ball bearings. Hold the drill so it is pointing up slightly so the washer and bearings do not fall out.
Step 9
Remove front screws
- Locate 4 screws on front of the drill. Remove using Torx T10
- Remove front casing piece.
Locate 4 screws on front of the drill. Remove using Torx T10
Remove front casing piece.
Step 10
Remove back screws
- Locate 4 screws on back of the drill.Remove using Torx T10.
- Remove back casing piece.
Locate 4 screws on back of the drill.Remove using Torx T10.
Remove back casing piece.
Step 11
Remove side screws
- Locate 4 screws on side of the drill. Remove using Torx T10
Locate 4 screws on side of the drill. Remove using Torx T10
Step 12
Case removal
- After all screws have been removed both side casings can be taken apart.
After all screws have been removed both side casings can be taken apart.
Step 13
Disconnect trigger
- Disconnect all wiring on top of trigger coming from motor and board.
Disconnect all wiring on top of trigger coming from motor and board.
Step 14
Connect new trigger
- Reconnect all wiring to your new trigger
Reconnect all wiring to your new trigger
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Daniel
Member since: 09/22/2014
143 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
USF Tampa, Team 2-3, Blackwell Fall 2014
Member of USF Tampa, Team 2-3, Blackwell Fall 2014
USFT-BLACKWELL-F14S2G3
5 Members
9 Guides authored
