Difficulty
Easy
Steps
13
Time Required
15 - 30 minutes
Sections
6
- Hopper and the Air Tank
- 2 steps
- Smart Parts Ion De-Gassing
- 2 steps
- Grip
- 2 steps
- Battery
- 1 step
- Separate Body From Grip Frame
- 4 steps
- Trigger
- 2 steps
Flags
0
BackSmart Parts Ion
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Hopper and the Air Tank
- Remove the air tank by rotating it counterclockwise.
- Do not pull the trigger or jostle the gun, there will still be pressurized air inside the gun that could be expelled and cause bodily harm if injected into eyes and/or skin.
- The pressure gauge will indicate the leftover air in the gun.
Remove the air tank by rotating it counterclockwise.
Do not pull the trigger or jostle the gun, there will still be pressurized air inside the gun that could be expelled and cause bodily harm if injected into eyes and/or skin.
The pressure gauge will indicate the leftover air in the gun.
1024
Step 2
- Remove the hopper by pulling it out of the feed tube, located on the top of the body. The hopper should easily come off when pulled straight up.
Remove the hopper by pulling it out of the feed tube, located on the top of the body. The hopper should easily come off when pulled straight up.
Step 3
Smart Parts Ion De-Gassing
- Turn the gun on by pressing the power button until the red light blinks.
- Turn vision mode off by pressing the power button again.
- Red light should be flashing in a double blink sequence.
Turn the gun on by pressing the power button until the red light blinks.
Turn vision mode off by pressing the power button again.
Red light should be flashing in a double blink sequence.
Step 4
- Pull the trigger to release the air in the gun.
- Pressurized air can be forceful, causing particles to be ejected from the gun into your eyes and/or skin. When air bubbles enter the bloodstream, they can block blood vessels, causing embolisms. To avoid this, make sure to point the gun in a safe direction when pulling the trigger because air will be released from the gun.
Pull the trigger to release the air in the gun.
Pressurized air can be forceful, causing particles to be ejected from the gun into your eyes and/or skin. When air bubbles enter the bloodstream, they can block blood vessels, causing embolisms. To avoid this, make sure to point the gun in a safe direction when pulling the trigger because air will be released from the gun.
Step 5
Grip
- Remove the four 8mm screws on each side of the gun’s grip using a Phillips #2 screwdriver.
Remove the four 8mm screws on each side of the gun’s grip using a Phillips #2 screwdriver.
Step 6
- Remove the grip by sliding it towards the front of the gun.
Remove the grip by sliding it towards the front of the gun.
Step 7
Battery
- Remove the 9V battery by unsnapping it.
Remove the 9V battery by unsnapping it.
Step 8
Separate Body From Grip Frame
- Remove the front and rear 1" screws on the gun’s grip frame using a 3/32" Allen Wrench.
Remove the front and rear 1" screws on the gun’s grip frame using a 3/32" Allen Wrench.
Step 9
- Remove the 12 mm screw on the top of the grip frame using a 3/32" Allen wrench.
Remove the 12 mm screw on the top of the grip frame using a 3/32" Allen wrench.
Step 10
- Separate the gun’s body from the frame by gently pulling them in opposite directions.
Separate the gun’s body from the frame by gently pulling them in opposite directions.
Step 11
- Remove the 1-1/4" screw that’s attached to the blue tube above the front grip using a 3/32" Allen Wrench.
Remove the 1-1/4" screw that’s attached to the blue tube above the front grip using a 3/32" Allen Wrench.
Step 12
Trigger
- Remove the trigger pin by tapping it out of the right side of the gun using a 3mm screwdriver.
- Any small tool can be used for this step instead of a 3mm screwdriver
Remove the trigger pin by tapping it out of the right side of the gun using a 3mm screwdriver.
Any small tool can be used for this step instead of a 3mm screwdriver
Step 13
- Remove the trigger by pulling it out.
Remove the trigger by pulling it out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Shane Villalpando
Member since: 02/02/2015
1,031 Reputation
10 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 8-42, Amido Winter 2015
Member of Cal Poly, Team 8-42, Amido Winter 2015
CPSU-AMIDO-W15S8G42
4 Members
10 Guides authored
