Featured
Featured Guide
Difficulty
Moderate
Steps
11
Time Required
15 - 20 minutes
Sections
2
- Binding
- 4 steps
- Binding Strap
- 7 steps
Flags
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackSnowboard
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Binding
- Release the binding straps by lifting up on the buckle and pulling towards the direction of the end of the ladder.
- Not all binding straps will release the same way. If you are having trouble releasing your binding straps, please refer to your owner’s manual.
Release the binding straps by lifting up on the buckle and pulling towards the direction of the end of the ladder.
Not all binding straps will release the same way. If you are having trouble releasing your binding straps, please refer to your owner’s manual.
1024
Step 2
- Move the straps and the highback plate out of the way in order to have clear access to the foot pad screw.
- The highback plate is the vertical support plate located on the heel side of the binding.
Move the straps and the highback plate out of the way in order to have clear access to the foot pad screw.
The highback plate is the vertical support plate located on the heel side of the binding.
Step 3
- Use a #2 Phillips screwdriver to remove the panhead, 10mm wide, M4 x 12mm screw located in the middle of the foot pad.
Use a #2 Phillips screwdriver to remove the panhead, 10mm wide, M4 x 12mm screw located in the middle of the foot pad.
Step 4
- Use a #2 Phillips screwdriver to remove the four ovalhead M6 x 12mm screws that attach the base plate of the binding to the board.
- Lift or slide the binding off the board and set the screws aside.
Use a #2 Phillips screwdriver to remove the four ovalhead M6 x 12mm screws that attach the base plate of the binding to the board.
Lift or slide the binding off the board and set the screws aside.
Step 5
Binding Strap
- Use a 5.5mm flathead screwdriver to anchor the backing bracket located on the inside of the binding.
- Using a Phillips #2 screwdriver, unscrew the countersunk ovalhead M4 x 16mm screw connecting the heel strap ladder to the binding.
Use a 5.5mm flathead screwdriver to anchor the backing bracket located on the inside of the binding.
Using a Phillips #2 screwdriver, unscrew the countersunk ovalhead M4 x 16mm screw connecting the heel strap ladder to the binding.
Step 6
- Unscrew the 10mm long thumb screw connecting the heel strap with its binding connector.
- Pull the heel strap apart from its binding connector.
Unscrew the 10mm long thumb screw connecting the heel strap with its binding connector.
Pull the heel strap apart from its binding connector.
Step 7
- Use a 5.5mm flathead screwdriver to anchor the backing bracket located on the inside of the binding.
- Using a Phillips #2 screwdriver, locate and unscrew the countersunk ovalhead M4 x 16mm screw holding the heel strap connector to the binding.
Using a Phillips #2 screwdriver, locate and unscrew the countersunk ovalhead M4 x 16mm screw holding the heel strap connector to the binding.
Step 8
- Flip the binding so that the bottom is accessible.
- Using your hands, pry off the plastic bottom covering starting at the toe end.
- The bottom may still remain attached on the heel edge. There is no need to completely remove it.
Flip the binding so that the bottom is accessible.
Using your hands, pry off the plastic bottom covering starting at the toe end.
The bottom may still remain attached on the heel edge. There is no need to completely remove it.
Step 9
- Remove the corner foam coverings by grabbing one edge and lifting up.
- Slide out the toe strap ladder.
Remove the corner foam coverings by grabbing one edge and lifting up.
Slide out the toe strap ladder.
Step 10
- Using a Phillips #2 screwdriver, unscrew the button head M4 x 10mm screw holding the toe strap with its connector.
- Slide the toe strap off of the toe strap connector.
Using a Phillips #2 screwdriver, unscrew the button head M4 x 10mm screw holding the toe strap with its connector.
Slide the toe strap off of the toe strap connector.
Step 11
- Turn the binding on its side and slide out the toe strap connector.
Turn the binding on its side and slide out the toe strap connector.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Robert Torres
Member since: 01/14/2014
214 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team 17-4, Forte Winter 2014
Member of Cal Poly, Team 17-4, Forte Winter 2014
CPSU-FORTE-W14S17G4
5 Members
7 Guides authored
