Difficulty
Moderate
Steps
22
Time Required
45 minutes - 1 hour
Sections
3
- SodaStream Source External Disassembly
- 5 steps
- SodaStream Source Internal Disassembly
- 15 steps
- Internal Carbonation Air Hose
- 2 steps
Flags
0
BackSodaStream Source
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
SodaStream Source External Disassembly
- Remove the soda bottle and the CO2 canister from the machine.
Remove the soda bottle and the CO2 canister from the machine.
1024
Step 2
- Remove the four 17.8 mm screws from the bottom metal base using a Phillips #1 screwdriver.
Remove the four 17.8 mm screws from the bottom metal base using a Phillips #1 screwdriver.
Step 3
- Pull the outer cover away from the front of the device.
Pull the outer cover away from the front of the device.
Step 4
- Remove the two 18.2 mm screws from the bottom of the front cover using a Phillips #1 screwdriver.
Remove the two 18.2 mm screws from the bottom of the front cover using a Phillips #1 screwdriver.
Step 5
- Firmly pull the front cover off.
- This piece is difficult to remove and requires force. It may help to use a wide, thin object to pry it off (like a Jimmy).
Firmly pull the front cover off.
This piece is difficult to remove and requires force. It may help to use a wide, thin object to pry it off (like a Jimmy).
Step 6
SodaStream Source Internal Disassembly
- Push the gold bar, located in the top of the device, out of the carbonating block.
- You can use the end of your screwdriver to push this piece out.
Push the gold bar, located in the top of the device, out of the carbonating block.
You can use the end of your screwdriver to push this piece out.
Step 7
- Slide the yellow battery cover up and away to remove it from the device.
Slide the yellow battery cover up and away to remove it from the device.
Step 8
- Unhook the bottom piece of the plastic arm on each side of the device.
Unhook the bottom piece of the plastic arm on each side of the device.
Step 9
- Lift the top of the plastic arm with the spudger and remove it on both sides.
Lift the top of the plastic arm with the spudger and remove it on both sides.
Step 10
- Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.
Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.
Step 11
- Remove the plastic oval and the spring within it.
Remove the plastic oval and the spring within it.
Step 12
- Pull the loader tab cover down and away from the rest of the carbonating block.
Pull the loader tab cover down and away from the rest of the carbonating block.
Step 13
- Remove the three 17.9 mm screws located on the right side.
- These screws may be difficult to access.
Remove the three 17.9 mm screws located on the right side.
These screws may be difficult to access.
Step 14
- Unhook the four clips on the top of the carbonating block and remove the plastic cover.
Unhook the four clips on the top of the carbonating block and remove the plastic cover.
Step 15
- Lift the clips located on both sides with the plastic spudger. Slide the front cover off.
Lift the clips located on both sides with the plastic spudger. Slide the front cover off.
Step 16
- Unhook the silver spring arms on both sides of the device by pushing down.
Unhook the silver spring arms on both sides of the device by pushing down.
Step 17
- Grip the right and left sides of the device and pull it into two identical halves.
- Once these two pieces are apart, all remaining internal components will fall out of the device.
Grip the right and left sides of the device and pull it into two identical halves.
Once these two pieces are apart, all remaining internal components will fall out of the device.
Step 18
- Pull the foam pad up and remove it from the front side of the carbonation component.
Pull the foam pad up and remove it from the front side of the carbonation component.
Step 19
- Remove the six 17.7 mm screws from the underside of the loader tab piece.
Remove the six 17.7 mm screws from the underside of the loader tab piece.
Step 20
- Pull the loader tab out of the nozzle.
Pull the loader tab out of the nozzle.
Step 21
Internal Carbonation Air Hose
- Use pliers to unscrew the gold cap piece from both ends of the tube
Use pliers to unscrew the gold cap piece from both ends of the tube
Step 22
- Detach the hose from both sides of the carbonation system.
- You will have to use force to detach this piece.
Detach the hose from both sides of the carbonation system.
You will have to use force to detach this piece.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
20 other people completed this guide.
Author
with 3 other contributors
Hailey Smith
Member since: 02/20/2017
1,231 Reputation
2 Guides authored
Badges:
19
+16 more badges
Team
USF Tampa, Team S1-G4, Leahy Spring 2017
Member of USF Tampa, Team S1-G4, Leahy Spring 2017
USFT-LEAHY-S17S1G4
3 Members
40 Guides authored
Nathan Roberts - Oct 17, 2017
Reply
Thanks for the guide, but i currently have this issue where the hose needs to be replaced, but no way of sourcing a spare part? Any clues anyone?
nagjoinslipknot - Jul 26, 2018
Did you ever find the part for your machine?
magnolia_ca - Oct 19, 2017
Reply
Where would you get this part
nagjoinslipknot - Jul 26, 2018
Reply
Exactly the same problem on my Source, but I can’t find spare parts anywhere.
Has anyone found where to get them from in Australia?
mark.jc.wright - Feb 1, 2020
did you ever find a supplier for the air hose replacement?
