Difficulty
Moderate
Steps
21
Time Required
45 minutes
Sections
3
- SodaStream Source External Disassembly
- 5 steps
- SodaStream Source Internal Disassembly
- 15 steps
- Internal Rubber Seal
- 1 step
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackSodaStream Source
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
SodaStream Source External Disassembly
- Remove the soda bottle and the CO2 canister from the machine.
Remove the soda bottle and the CO2 canister from the machine.
1024
Step 2
- Remove the four 17.8 mm screws from the bottom metal base using a Phillips #1 screwdriver.
Remove the four 17.8 mm screws from the bottom metal base using a Phillips #1 screwdriver.
Step 3
- Pull the outer cover away from the front of the device.
Pull the outer cover away from the front of the device.
Step 4
- Remove the two 18.2 mm screws from the bottom of the front cover using a Phillips #1 screwdriver.
Remove the two 18.2 mm screws from the bottom of the front cover using a Phillips #1 screwdriver.
Step 5
- Firmly pull the front cover off.
- This piece is difficult to remove and requires force. It may help to use a wide, thin object to pry it off (like a Jimmy).
Firmly pull the front cover off.
This piece is difficult to remove and requires force. It may help to use a wide, thin object to pry it off (like a Jimmy).
Step 6
SodaStream Source Internal Disassembly
- Push the gold bar, located in the top of the device, out of the carbonating block.
- You can use the end of your screwdriver to push this piece out.
Push the gold bar, located in the top of the device, out of the carbonating block.
You can use the end of your screwdriver to push this piece out.
Step 7
- Slide the yellow battery cover up and away to remove it from the device.
Slide the yellow battery cover up and away to remove it from the device.
Step 8
- Unhook the bottom piece of the plastic arm on each side of the device.
Unhook the bottom piece of the plastic arm on each side of the device.
Step 9
- Lift the top of the plastic arm with the spudger and remove it on both sides.
Lift the top of the plastic arm with the spudger and remove it on both sides.
Step 10
- Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.
Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.
Step 11
- Remove the plastic oval and the spring within it.
Remove the plastic oval and the spring within it.
Step 12
- Pull the loader tab cover down and away from the rest of the carbonating block.
Pull the loader tab cover down and away from the rest of the carbonating block.
Step 13
- Remove the three 17.9 mm screws located on the right side.
- These screws may be difficult to access.
Remove the three 17.9 mm screws located on the right side.
These screws may be difficult to access.
Step 14
- Unhook the four clips on the top of the carbonating block and remove the plastic cover.
Unhook the four clips on the top of the carbonating block and remove the plastic cover.
Step 15
- Lift the clips located on both sides with the plastic spudger. Slide the front cover off.
Lift the clips located on both sides with the plastic spudger. Slide the front cover off.
Step 16
- Unhook the silver spring arms on both sides of the device by pushing down.
Unhook the silver spring arms on both sides of the device by pushing down.
Step 17
- Grip the right and left sides of the device and pull it into two identical halves.
- Once these two pieces are apart, all remaining internal components will fall out of the device.
Grip the right and left sides of the device and pull it into two identical halves.
Once these two pieces are apart, all remaining internal components will fall out of the device.
Step 18
- Pull the foam pad up and remove it from the front side of the carbonation component.
Pull the foam pad up and remove it from the front side of the carbonation component.
Step 19
- Remove the six 17.7 mm screws from the underside of the loader tab piece.
Remove the six 17.7 mm screws from the underside of the loader tab piece.
Step 20
- Pull the loader tab out of the nozzle.
Pull the loader tab out of the nozzle.
Step 21
Internal Rubber Seal
- Remove the rubber seal from the nozzle piece and replace with the new seal.
Remove the rubber seal from the nozzle piece and replace with the new seal.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
24 other people completed this guide.
Author
with 3 other contributors
Alexandra I Curtis
Member since: 02/20/2017
836 Reputation
2 Guides authored
Badges:
15
+12 more badges
Team
USF Tampa, Team S1-G4, Leahy Spring 2017
Member of USF Tampa, Team S1-G4, Leahy Spring 2017
USFT-LEAHY-S17S1G4
3 Members
40 Guides authored
Ron Hayes - Aug 11, 2017
Reply
Where can I purchase the internal rubber seal? Thanks Ronzo (Australia)
Peter De Luca - Jan 23, 2018
Reply
I’ll ask the same question as the gentleman above. Where can I purchase the rubber gasket seal? I cannot find it anywhere online. I would also like to purchase the gas delivery tube and is installed.
Thank you
Peter (USA)
Juha Heikkilä - Feb 25, 2018
Reply
Our sodastream does not work anymore. It’s the electrick model with three different gasfillings. When you put the waterbottle into the filling station and then you turn your suitably filled bottle down and you try to push some of those lights (- /–/ —) for to fill your bottle, it sounds like little choked “puff” and then all lights are blinking (I think they tell mailfunction). No gas comes. I have changed new and stuffed gasbottle, power cable is its place and works. So what’s wrong? Thank You allready, Juha Heikkilä (Finland).
Claude Vadeboncoeur - Feb 26, 2018
Reply
I can’t remove the outer cover, step 3.
Zuzana Karlíková - Jun 27, 2018
Reply
I am also looking for a gasket. Do you have any advice?
