Difficulty

Moderate

Steps

6

Time Required

                          20 minutes - 1 hour

Sections

1

  • Battery
  • 6 steps

Flags

2

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackSol Republic Deck

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • With plastic spudger wedge in between the top and bottom casings to force sepearation . Exposing the inside components of the Republic Deck.

With plastic spudger wedge in between the top and bottom casings to force sepearation . Exposing the inside components of the Republic Deck.

1024

Step 2

  • Use the screwdriver to unscrew 2 3.63mm Phillips #0 screws securing the plastic plate.

Use the screwdriver to unscrew 2 3.63mm Phillips #0 screws securing the plastic plate.

Step 3

  • Remove ribbon cable from the circuit board.

Remove ribbon cable from the circuit board.

Step 4

  • Unscrew five 3.6 mm Phillips #0 screws securing the circuit board.
  • The ribbon cables are adhesive attached to the case, use tweezers to VERY carefully pick them up. They will then lift up with the circuit board. Or desolder them at the bottom to separate from the circuit board.
  • Melt the solder with an iron and used the tweezers to pull the wire upright.
  • You can pull the circuit board up and away from the wires once the wires are pointed up.

Unscrew five 3.6 mm Phillips #0 screws securing the circuit board.

The ribbon cables are adhesive attached to the case, use tweezers to VERY carefully pick them up. They will then lift up with the circuit board. Or desolder them at the bottom to separate from the circuit board.

Melt the solder with an iron and used the tweezers to pull the wire upright.

You can pull the circuit board up and away from the wires once the wires are pointed up.

Step 5

  • Unscrew eighteen 6.2 mm Phillips #0 screws and lift the black plastic plate from the case.

Unscrew eighteen 6.2 mm Phillips #0 screws and lift the black plastic plate from the case.

Step 6

  • Unscrew both 3.6 mm Phillips #0 screws holding the battery case to the back of the plastic plate.
  • Remove the battery from the battery case.
  • Original battery is ICR18650-30A. Its rated for 3000mAh, 6A continuous (2 C-rate).

Unscrew both 3.6 mm Phillips #0 screws holding the battery case to the back of the plastic plate.

Remove the battery from the battery case.

Original battery is ICR18650-30A. Its rated for 3000mAh, 6A continuous (2 C-rate).

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 4 other contributors 


                    Ross Bolton

Member since: 03/21/2017

133 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       IUPUI, Team S3-G1, Baechle Spring 2017                        

                                                  Member of IUPUI, Team S3-G1, Baechle Spring 2017 



                    IUPUI-BAECHLE-S17S3G1                     


                                            3 Members                     


                                            3 Guides authored

chai4i - Jun 3, 2017

Reply

I appreciate the battery replacement for the deck,but what about battery replacement

For the deck ultra

Peter Perez - Feb 1, 2018

Reply

What type of battery is it?

Aaron Linn - Feb 10, 2019

Reply

It’s just a regular lithium ion 18650 battery 3.7v 3200-3500 mah. The deck ultra uses 2 of these

vineeth m - Apr 5, 2019

The wires which are blue and purple are connected to battery body if im not wrong

vineeth m - Apr 3, 2019

Reply

After changing the battery my device is not switching on. Please help. I connected the charger the battery is charging… showing red.