Solio Classic2 Usb Port Replacement Repair Guide

Difficulty

Difficult

Steps

9

Time Required

                          30 - 45 minutes            

Sections

3

• Disconnecting the Battery
• 6 steps
• Circuit Board
• 2 steps
• USB Port
• 1 step

Flags

0

• BackSolio CLASSIC2

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Disconnecting the Battery               

• Turn off the device by pressing on the clear power button behind the device.
• To make sure that it is off, make sure the button is not flashing green.

Turn off the device by pressing on the clear power button behind the device.

To make sure that it is off, make sure the button is not flashing green.

1024

Step 2

• Using the Phillips #1 screwdriver, remove the 2mm screw located on the bottom of the device, near the hinge.

Using the Phillips #1 screwdriver, remove the 2mm screw located on the bottom of the device, near the hinge.

Step 3

• Using the plastic opening tools, gently pry open the side of the large panel.
• Keeping the tool in, slowly slide the tool along the side of the panel.

Using the plastic opening tools, gently pry open the side of the large panel.

Keeping the tool in, slowly slide the tool along the side of the panel.

Step 4

• Rotate the device 180 degrees.
• Make sure the opening on other side of the device does not snap closed.
• Gently slide the plastic opening tool along the side of the panel.

Rotate the device 180 degrees.

Make sure the opening on other side of the device does not snap closed.

Gently slide the plastic opening tool along the side of the panel.

Step 5

• Do not fully pull apart the back panel from the device. Doing so can rip the two red and blue wires attached to the panel.
• Using both hands, slowly pull apart the back panel from the rest of the device.
• Gently flip the back panel open so the circuit board faces up and the two panels are side by side.

Do not fully pull apart the back panel from the device. Doing so can rip the two red and blue wires attached to the panel.

Using both hands, slowly pull apart the back panel from the rest of the device.

Gently flip the back panel open so the circuit board faces up and the two panels are side by side.

Step 6

• Softly pinch the red and blue wires close to the white connector.
• To pull the wires out, wiggle them back and forth until the connector is fully out.

Softly pinch the red and blue wires close to the white connector.

To pull the wires out, wiggle them back and forth until the connector is fully out.

Step 7

              Circuit Board               

• Unscrew the three 2mm screws holding the circuit board down using a Phillips #1 screwdriver.

Unscrew the three 2mm screws holding the circuit board down using a Phillips #1 screwdriver.

Step 8

• Make sure the white USB port cover on the side of the device is pulled out or you won’t be able to lift the circuit board.
• Gently lift the circuit board out of the device using tweezers.

Make sure the white USB port cover on the side of the device is pulled out or you won’t be able to lift the circuit board.

Gently lift the circuit board out of the device using tweezers.

Step 9

              USB Port               

• Soldering can melt key components and cause harm to both the user and the device. Read soldering guide before attempting.
• Remove solder from both spots on outside of the USB port.
• Remove solder from base of the USB port.

Soldering can melt key components and cause harm to both the user and the device. Read soldering guide before attempting.

Remove solder from both spots on outside of the USB port.

Remove solder from base of the USB port.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 

                    Anthony Ramos                     

Member since: 10/20/2013

102 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge                           

Team

                       Cal Poly, Team 4-28, Amido Fall 2013                        

                                                  Member of Cal Poly, Team 4-28, Amido Fall 2013 



                    CPSU-AMIDO-F13S4G28                     


                                            4 Members                     


                                            7 Guides authored