Difficulty

Moderate

Steps

12

Time Required

                          20 - 40 minutes

Sections

2

  • Battery
  • 4 steps
  • Back Case
  • 8 steps

Flags

0

  • BackSony α6000

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Begin by placing the camera facing upside down.

Begin by placing the camera facing upside down.

1024

Step 2

  • Slide the notched locking bar on the battery compartment from LOCK to OPEN.

Slide the notched locking bar on the battery compartment from LOCK to OPEN.

Step 3

  • Push the small blue bar horizontally off of the battery.

Push the small blue bar horizontally off of the battery.

Step 4

  • Extract the battery.

Extract the battery.

Step 5

              Back Case
  • Position the camera with the bottom facing upwards and the lens facing away from you.
  • Slide the notched locking bar on the battery compartment from LOCK to OPEN.

Position the camera with the bottom facing upwards and the lens facing away from you.

Step 6

  • Once the battery is removed, use a Phillips #00 screwdriver to remove the three screws at the bottom of the battery compartment.

Once the battery is removed, use a Phillips #00 screwdriver to remove the three screws at the bottom of the battery compartment.

Step 7

  • Use the Phillips #00 screwdriver to remove the screws located next to the camera strap.
  • There may be screws on either side by the camera strap mounts. If removing the screw on the left side doesn’t sufficiently loosen the case, be sure to check for a screw on the other side before resorting to excessive force.

Use the Phillips #00 screwdriver to remove the screws located next to the camera strap.

There may be screws on either side by the camera strap mounts. If removing the screw on the left side doesn’t sufficiently loosen the case, be sure to check for a screw on the other side before resorting to excessive force.

Step 8

  • Position the camera with the battery housing facing upwards.
  • Remove the two screws on the bottom of the camera using the Phillips #00 screwdriver.

Position the camera with the battery housing facing upwards.

Remove the two screws on the bottom of the camera using the Phillips #00 screwdriver.

Step 9

  • Position the camera with the flash assembly facing upwards.
  • Remove the screw located underneath with a Phillips #00 screwdriver.

Position the camera with the flash assembly facing upwards.

Remove the screw located underneath with a Phillips #00 screwdriver.

Step 10

  • Pull back the LCD screen.
  • Remove the three screws directly underneath using the Phillips #00 screwdriver.

Pull back the LCD screen.

Remove the three screws directly underneath using the Phillips #00 screwdriver.

Step 11

  • Gently pop off the top case of the camera using your fingers or a plastic opening tool.
  • If using a plastic opening tool, ensure that the pressure is being applied to the plastic rather than the metal.

Gently pop off the top case of the camera using your fingers or a plastic opening tool.

If using a plastic opening tool, ensure that the pressure is being applied to the plastic rather than the metal.

Step 12

  • Position the camera with the LCD screen facing upwards.
  • Pull back the LCD screen.
  • Gently remove the back case guiding it around the LCD screen.

Position the camera with the LCD screen facing upwards.

Gently remove the back case guiding it around the LCD screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Ryan Bilitski

Member since: 10/02/2019

178 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       The Citadel Military College of South Carolina, Team S2-G3, Eggleston Fall 2019                        

                                                  Member of The Citadel Military College of South Carolina, Team S2-G3, Eggleston Fall 2019 



                    CMCSC-EGGLESTON-F19S2G3                     


                                            3 Members                     


                                            5 Guides authored