Difficulty
Moderate
Steps
11
Time Required
25 minutes
Sections
3
- Front Case
- 5 steps
- Eye Cup
- 3 steps
- Rear Case
- 3 steps
Flags
0
BackSony Alpha A350
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Case
- Using a Phillips #00 Screwdriver, remove the four 5.5mm screws from the bottom of the camera.
- Using a Phillips #00 Screwdriver, remove the one 4.3mm screw.
Using a Phillips #00 Screwdriver, remove the four 5.5mm screws from the bottom of the camera.
Using a Phillips #00 Screwdriver, remove the one 4.3mm screw.
1024
Step 2
- Using a Phillips #00 screwdriver, remove one 3.6mm screw on the left side of the camera.
- Open the remote / DC under the rubber flap to reveal a screw.
- Using the Phillips #00 screwdriver, remove one 4.3mm screw.
Using a Phillips #00 screwdriver, remove one 3.6mm screw on the left side of the camera.
Open the remote / DC under the rubber flap to reveal a screw.
Using the Phillips #00 screwdriver, remove one 4.3mm screw.
Step 3
- Open the flash on the top of the camera and remove two 4.3mm screws with a Phillips #00 screwdriver.
- If the spring guard falls out during deconstruction, gently place the guard over the spring during construction.
- To open the flash, simply press the button on the left side.
Open the flash on the top of the camera and remove two 4.3mm screws with a Phillips #00 screwdriver.
If the spring guard falls out during deconstruction, gently place the guard over the spring during construction.
To open the flash, simply press the button on the left side.
Step 4
- Open the plastic SD card door.
- Using Phillips #00 screwdriver, remove two 4.4 mm screws outside and two 4.4mm screws inside the door.
Open the plastic SD card door.
Using Phillips #00 screwdriver, remove two 4.4 mm screws outside and two 4.4mm screws inside the door.
Step 5
- Gently pull the outer front case from the camera.
- It should fall apart easily if all screws are removed.
Gently pull the outer front case from the camera.
It should fall apart easily if all screws are removed.
Step 6
Eye Cup
- Identify the bottom of the eye cup
- Using the heavy duty spudger, push the eye cup upward to remove it from the camera body.
Identify the bottom of the eye cup
Using the heavy duty spudger, push the eye cup upward to remove it from the camera body.
Step 7
- Using the Phillips #000 screwdriver, unscrew the two screws from the eye cup.
- Remove the back side of the eye cup.
Using the Phillips #000 screwdriver, unscrew the two screws from the eye cup.
Remove the back side of the eye cup.
Step 8
- Push down on the hard plastic part of the eye cup and remove it from the cushion.
Push down on the hard plastic part of the eye cup and remove it from the cushion.
Step 9
Rear Case
- Using a Phillips #00 screwdriver, remove the two 4.3mm screws attaching the ribbons to the front case.
Using a Phillips #00 screwdriver, remove the two 4.3mm screws attaching the ribbons to the front case.
Step 10
- After taking off the eye cup, remove two screws using a Phillips #00 screwdriver.
After taking off the eye cup, remove two screws using a Phillips #00 screwdriver.
Step 11
- Gently pry the rear case off of the body of the camera using your hands or a spudger.
Gently pry the rear case off of the body of the camera using your hands or a spudger.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Danielle Trivett
Member since: 11/04/2019
337 Reputation
3 Guides authored
Badges:
5
+2 more badges
Team
IUPUI, Team S1-G6, Henning Fall 2019
Member of IUPUI, Team S1-G6, Henning Fall 2019
IUPUI-HENNING-F19S1G6
3 Members
6 Guides authored
