Difficulty

Difficult

Steps

12

Time Required

                          15 minutes

Sections

2

  • Battery Replacement
  • 4 steps
  • Screen
  • 8 steps

Flags

0

  • BackSony Alpha ILCE-6000

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery Replacement
  • Turn off the camera by sliding the power switch to OFF.

Turn off the camera by sliding the power switch to OFF.

1024

Step 2

  • Flip the camera upside down and locate the battery compartment.
  • Slide the compartment lock to OPEN to unlock it.

Flip the camera upside down and locate the battery compartment.

Slide the compartment lock to OPEN to unlock it.

Step 3

  • Locate the blue lever that keeps the battery in place.
  • Push the blue lever back to release battery.

Locate the blue lever that keeps the battery in place.

Push the blue lever back to release battery.

Step 4

  • Once the battery is free, you are able to take the battery out of the compartment.

Once the battery is free, you are able to take the battery out of the compartment.

Step 5

              Screen
  • Flip the camera to the bottom side. Using screwdriver, remove the two screws located on the bottom of camera screen.
  • Flip the camera back over, locate the two other 3mm screws behind the screen and remove them.

Flip the camera to the bottom side. Using screwdriver, remove the two screws located on the bottom of camera screen.

Flip the camera back over, locate the two other 3mm screws behind the screen and remove them.

Step 6

  • Gently pry open the screen backplate.

Gently pry open the screen backplate.

Step 7

  • Gently pry off the plastic cover at the top of the screen.

Gently pry off the plastic cover at the top of the screen.

Step 8

  • Carefully remove the clip located at the top of the screen.

Carefully remove the clip located at the top of the screen.

Step 9

  • Flip the camera so that it is bottom side up. Pry off the inner support plate.

Flip the camera so that it is bottom side up. Pry off the inner support plate.

Step 10

  • Gently wiggle the screen’s ribbon cable until it comes free from the white slot.

Gently wiggle the screen’s ribbon cable until it comes free from the white slot.

Step 11

  • Pry apart the metal backplate and remove it.

Pry apart the metal backplate and remove it.

Step 12

  • Gently remove the old screen, and replace it with the new one.

Gently remove the old screen, and replace it with the new one.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 4 other contributors 


                    Tony Au

Member since: 02/02/2017

342 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UW Tacoma, Team 1-4, Rose Winter 2017                        

                                                  Member of UW Tacoma, Team 1-4, Rose Winter 2017 



                    UWT-ROSE-W17S1G4                     


                                            4 Members                     


                                            10 Guides authored

Claire Sweet - Apr 9, 2019

Reply

This is super helpful! Where did you purchase your replacement part from?

Christopher St.Louis - Jun 4, 2020

Reply

The white connector opens by prying up the black part. What about the little black connector?

Kevin Ketelaars - Jan 14, 2022

Just comes out when you pull on it gently

Kevin Ketelaars - Jan 14, 2022

Reply

Top left screw on back plate is a pain to put back in at an angle with magnetized JIS driver. Non magnetized or slightly loose fitting driver might help.

Trick is to get the screw fit in the thread at the right angle, then drive it in with the driver at an angle.