Difficulty
Moderate
Steps
13
Time Required
15 - 20 minutes
Sections
3
- Outer Cover
- 5 steps
- Disk Tray
- 4 steps
- Disk Reader
- 4 steps
Flags
1
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
BackSony BDP-BX510
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Cover
- Plug in the device to turn it on, then press the eject ( ⏏ ) button to open the tray.
Plug in the device to turn it on, then press the eject ( ⏏ ) button to open the tray.
1024
Step 2
- To remove the tray cover, hold both sides of the tray cover and gently apply a downward pressure.
- Apply slightly more pressure to the left side until it unhooks then unhook the right side.
- Close the disk tray by pressing the eject button again, then power off the device and unplug it.
- Do not use too much force to remove the tray cover as you may break it.
To remove the tray cover, hold both sides of the tray cover and gently apply a downward pressure.
Apply slightly more pressure to the left side until it unhooks then unhook the right side.
Close the disk tray by pressing the eject button again, then power off the device and unplug it.
Do not use too much force to remove the tray cover as you may break it.
Step 3
- Turn to the back of the device.
- Remove the two 7mm Phillips #2 screws.
- Slide the two plastic covers on both sides of the device towards the back of the device to remove them.
Turn to the back of the device.
Remove the two 7mm Phillips #2 screws.
Slide the two plastic covers on both sides of the device towards the back of the device to remove them.
Step 4
- Turn the device so you can see the bottom.
- Unclip the three black plastic clips on the bottom of the device.
- Unclip one clip on each side of the device.
Turn the device so you can see the bottom.
Unclip the three black plastic clips on the bottom of the device.
Unclip one clip on each side of the device.
Step 5
- Slide the cover forward to remove.
Slide the cover forward to remove.
Step 6
Disk Tray
- Pull the medium-sized 9 pin ribbon cable and the small 5 pin ribbon cable out of their connector in the motherboard.
- Using tweezers, lift the black tab on the connector of the large 45 pin connector on the motherboard.
- Pull the large 45 pin ribbon cable out of the connector in the motherboard.
- Be very careful. The goal is to slightly lift the pin connector, not to completely detach it. Do not forcibly pull.
Pull the medium-sized 9 pin ribbon cable and the small 5 pin ribbon cable out of their connector in the motherboard.
Using tweezers, lift the black tab on the connector of the large 45 pin connector on the motherboard.
Pull the large 45 pin ribbon cable out of the connector in the motherboard.
Be very careful. The goal is to slightly lift the pin connector, not to completely detach it. Do not forcibly pull.
Step 7
- Remove the 5mm Phillips #2 screw holding the metal brace above the disk tray.
- Remove the two 5mm Phillips #2 screws that hold the disk tray to the metal case on the bottom.
Remove the 5mm Phillips #2 screw holding the metal brace above the disk tray.
Remove the two 5mm Phillips #2 screws that hold the disk tray to the metal case on the bottom.
Step 8
- Turn the device over to the backside.
- Use tweezers or hands to take off the metal clasp for the metal brace near the center on the bottom of the device.
Turn the device over to the backside.
Use tweezers or hands to take off the metal clasp for the metal brace near the center on the bottom of the device.
Step 9
- Remove the metal brace then remove the disk tray.
Remove the metal brace then remove the disk tray.
Step 10
Disk Reader
- Connect the three cables.
- Plug the device in and press the eject button to open the disk tray.
- Unplug the device.
- Disconnect the three cables.
Connect the three cables.
Plug the device in and press the eject button to open the disk tray.
Unplug the device.
Disconnect the three cables.
Step 11
- Locate and unclip the plastic clips on the sides of the disk tray using a metal spudger. There are two on each side of the disk tray.
- Lift open and remove the top cover of the disk tray.
- Remove the two 6mm Phillips #0 screws from the disk reader.
Locate and unclip the plastic clips on the sides of the disk tray using a metal spudger. There are two on each side of the disk tray.
Lift open and remove the top cover of the disk tray.
Remove the two 6mm Phillips #0 screws from the disk reader.
Step 12
- Using tweezers, lift the black tab on the connector of the large ribbon cable on the disk reader.
- Pull the large ribbon cable out of the connector in the disk reader.
- Do not forcibly pull out the large ribbon cable as you could damage it. Once the black tab is lifted it should come out easily.
Using tweezers, lift the black tab on the connector of the large ribbon cable on the disk reader.
Pull the large ribbon cable out of the connector in the disk reader.
Do not forcibly pull out the large ribbon cable as you could damage it. Once the black tab is lifted it should come out easily.
Step 13
- Lift the disk reader carefully.
- Do not lift the disk reader roughly as there is small cable attached to it.
- Pull the small ribbon cable out of the disk reader.
Lift the disk reader carefully.
Do not lift the disk reader roughly as there is small cable attached to it.
Pull the small ribbon cable out of the disk reader.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Tae (Tim) Im
Member since: 01/14/2020
279 Reputation
3 Guides authored
Badges:
5
+2 more badges
Team
York University, Team S1-G10, Woodhouse Winter 2020
Member of York University, Team S1-G10, Woodhouse Winter 2020
YORK-WOODHOUSE-W20S1G10
2 Members
6 Guides authored
