Difficulty

Moderate

Steps

10

Time Required

                          10 - 15 minutes

Sections

2

  • Outer Cover
  • 5 steps
  • Motherboard
  • 5 steps

Flags

0

  • BackSony BDP-BX510

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Outer Cover
  • Plug in the device to turn it on, then press the eject ( ⏏ ) button to open the tray.

Plug in the device to turn it on, then press the eject ( ⏏ ) button to open the tray.

1024

Step 2

  • To remove the tray cover, hold both sides of the tray cover and gently apply a downward pressure.
  • Apply slightly more pressure to the left side until it unhooks then unhook the right side.
  • Close the disk tray by pressing the eject button again, then power off the device and unplug it.
  • Do not use too much force to remove the tray cover as you may break it.

To remove the tray cover, hold both sides of the tray cover and gently apply a downward pressure.

Apply slightly more pressure to the left side until it unhooks then unhook the right side.

Close the disk tray by pressing the eject button again, then power off the device and unplug it.

Do not use too much force to remove the tray cover as you may break it.

Step 3

  • Turn to the back of the device.
  • Remove the two 7mm Phillips #2 screws.
  • Slide the two plastic covers on both sides of the device towards the back of the device to remove them.

Turn to the back of the device.

Remove the two 7mm Phillips #2 screws.

Slide the two plastic covers on both sides of the device towards the back of the device to remove them.

Step 4

  • Turn the device so you can see the bottom.
  • Unclip the three black plastic clips on the bottom of the device.
  • Unclip one clip on each side of the device.

Turn the device so you can see the bottom.

Unclip the three black plastic clips on the bottom of the device.

Unclip one clip on each side of the device.

Step 5

  • Slide the cover forward to remove.

Slide the cover forward to remove.

Step 6

              Motherboard
  • Pull out the power cord from the device.

Pull out the power cord from the device.

Step 7

  • Pull out these cables from the motherboard.
  • Using tweezers, lift the black tab on the connector of the large 45 pin connector on the motherboard.
  • Pull the large 45 pin ribbon cable out of the connector in the motherboard.
  • Do not use excessive force to remove the cables and do not forcibly pull out the 45 pin ribbon cable as you could damage it. Once the black tab is lifted it should come out easily.

Pull out these cables from the motherboard.

Using tweezers, lift the black tab on the connector of the large 45 pin connector on the motherboard.

Pull the large 45 pin ribbon cable out of the connector in the motherboard.

Do not use excessive force to remove the cables and do not forcibly pull out the 45 pin ribbon cable as you could damage it. Once the black tab is lifted it should come out easily.

Step 8

  • Remove the two 5mm Phillips #1 screws.
  • Lift the side of the power module and remove it.

Remove the two 5mm Phillips #1 screws.

Lift the side of the power module and remove it.

Step 9

  • Remove the three 5mm Phillips #1 screws.
  • Turn the device over to the backside.
  • Use tweezers or metal spudger to take off the metal clasp for the metal brace near the center on the bottom of the device.
  • Remove the metal brace.

Remove the three 5mm Phillips #1 screws.

Turn the device over to the backside.

Use tweezers or metal spudger to take off the metal clasp for the metal brace near the center on the bottom of the device.

Remove the metal brace.

Step 10

  • Turn to the back of the device.
  • Remove the silver 3mm Phillips #1 screw.
  • Remove the black 7mm Phillips #1 screw.
  • Lift the side of the motherboard and pull it out.

Remove the silver 3mm Phillips #1 screw.

Remove the black 7mm Phillips #1 screw.

Lift the side of the motherboard and pull it out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Tae (Tim) Im

Member since: 01/14/2020

279 Reputation

                                      3 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       York University, Team S1-G10, Woodhouse Winter 2020                        

                                                  Member of York University, Team S1-G10, Woodhouse Winter 2020 



                    YORK-WOODHOUSE-W20S1G10                     


                                            2 Members                     


                                            6 Guides authored