Difficulty

Moderate

Steps

12

Time Required

                          15 - 20 minutes

Sections

3

  • Outer Cover
  • 5 steps
  • Port Board
  • 4 steps
  • Wi-Fi Module
  • 3 steps

Flags

0

  • BackSony BDP-BX510

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Outer Cover
  • Plug in the device to turn it on, then press the eject ( ⏏ ) button to open the tray.

Plug in the device to turn it on, then press the eject ( ⏏ ) button to open the tray.

1024

Step 2

  • To remove the tray cover, hold both sides of the tray cover and gently apply a downward pressure.
  • Apply slightly more pressure to the left side until it unhooks then unhook the right side.
  • Close the disk tray by pressing the eject button again, then power off the device and unplug it.
  • Do not use too much force to remove the tray cover as you may break it.

To remove the tray cover, hold both sides of the tray cover and gently apply a downward pressure.

Apply slightly more pressure to the left side until it unhooks then unhook the right side.

Close the disk tray by pressing the eject button again, then power off the device and unplug it.

Do not use too much force to remove the tray cover as you may break it.

Step 3

  • Turn to the back of the device.
  • Remove the two 7mm Phillips #2 screws.
  • Slide the two plastic covers on both sides of the device towards the back of the device to remove them.

Turn to the back of the device.

Remove the two 7mm Phillips #2 screws.

Slide the two plastic covers on both sides of the device towards the back of the device to remove them.

Step 4

  • Turn the device so you can see the bottom.
  • Unclip the three black plastic clips on the bottom of the device.
  • Unclip one clip on each side of the device.

Turn the device so you can see the bottom.

Unclip the three black plastic clips on the bottom of the device.

Unclip one clip on each side of the device.

Step 5

  • Slide the cover forward to remove.

Slide the cover forward to remove.

Step 6

              Port Board
  • Find the large ribbon cable that connects the port board to the motherboard.
  • Carefully pull directly upwards to disconnect the cable.

Find the large ribbon cable that connects the port board to the motherboard.

Carefully pull directly upwards to disconnect the cable.

Step 7

  • Using the Phillips #1 screwdriver, remove the 5mm screwdriver attached to the port board.

Using the Phillips #1 screwdriver, remove the 5mm screwdriver attached to the port board.

Step 8

  • Unclip the metal piece on the lower right corner by gently lifting it up.

Unclip the metal piece on the lower right corner by gently lifting it up.

Step 9

  • Remove the port board by simply pulling it away from the device.

Remove the port board by simply pulling it away from the device.

Step 10

              Wi-Fi Module
  • Pull the cable that attaches the Wi-Fi module to the motherboard.
  • The cable will be hard to remove, so pull hard but carefully.

Pull the cable that attaches the Wi-Fi module to the motherboard.

The cable will be hard to remove, so pull hard but carefully.

Step 11

  • Use a Phillips #1 screwdriver to remove the single 5mm screw that holds Wi-Fi module to the device.

Use a Phillips #1 screwdriver to remove the single 5mm screw that holds Wi-Fi module to the device.

Step 12

  • Carefully remove the Wi-Fi module from the device.
  • Avoid getting fingerprints on the module.

Carefully remove the Wi-Fi module from the device.

Avoid getting fingerprints on the module.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Niki Ngosi

Member since: 01/19/2020

375 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       York University, Team S1-G10, Woodhouse Winter 2020                        

                                                  Member of York University, Team S1-G10, Woodhouse Winter 2020 



                    YORK-WOODHOUSE-W20S1G10                     


                                            2 Members                     


                                            6 Guides authored