Sony Bdp S1 Fan Replacement Repair Guide

Difficulty

Moderate

Steps

6

Time Required

                          20 minutes            

Sections

2

• Sony BDP-S1: Getting inside the device
• 4 steps
• Fan
• 2 steps

Flags

Missed a Step

Oops! This guide is currently missing some important steps.

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

• BackSony BDP-S1

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Sony BDP-S1: Getting inside the device               

• Remove the 12mm screws with the Philips #2 screwdriver which keep the plastic panels in place.
• Don’t forget, there are two more 12mm screws on the other side as well.

Remove the 12mm screws with the Philips #2 screwdriver which keep the plastic panels in place.

Don’t forget, there are two more 12mm screws on the other side as well.

1024

Step 2

• First, remove the three 12mm black screws holding the top panel on (Phillips #2).
• Then, remove the two 12mm black screws - one on each side of the back of the device - holding the top panel on.
• Lastly, remove the three 12mm black screws on each side of device.

First, remove the three 12mm black screws holding the top panel on (Phillips #2).

Then, remove the two 12mm black screws - one on each side of the back of the device - holding the top panel on.

Lastly, remove the three 12mm black screws on each side of device.

Step 3

• Carefully lift up the top panel, because there are two blue ribbon cables that must be disconnected before removing the panel, and we do NOT want them to break.
• After gently disconnecting the two ribbon cables (you can just pull them out with your hand), take the top off and set it to the side.

Carefully lift up the top panel, because there are two blue ribbon cables that must be disconnected before removing the panel, and we do NOT want them to break.

After gently disconnecting the two ribbon cables (you can just pull them out with your hand), take the top off and set it to the side.

Step 4

• After the top is off, you’ll see that there are two metal bars that go across the top of the device.
• Remove each bar by unscrewing the two 10mm silver screws on each end.

After the top is off, you’ll see that there are two metal bars that go across the top of the device.

Remove each bar by unscrewing the two 10mm silver screws on each end.

Step 5

              Fan               

• First we need to unscrew the fan from before we can remove it.
• Remove both copper colored 10mm screws with a #2 phillips screwdriver.
• As you remove the second screw, pull the fan inward to remove it from the remainder of the case. It should now only be connected to the case through a cable attached to the circuit board.
• The disk drive is removed in the pictures, however this is not necessary to replace the fan and can be ignored.

First we need to unscrew the fan from before we can remove it.

Remove both copper colored 10mm screws with a #2 phillips screwdriver.

As you remove the second screw, pull the fan inward to remove it from the remainder of the case. It should now only be connected to the case through a cable attached to the circuit board.

The disk drive is removed in the pictures, however this is not necessary to replace the fan and can be ignored.

Step 6

• We will now completely remove the fan from the player.
• Carefully detach the cable from the fan to the circuit board by pulling on the cable connecting the fan to the circuit board.
• You are now ready to install the new fan!

We will now completely remove the fan from the player.

Carefully detach the cable from the fan to the circuit board by pulling on the cable connecting the fan to the circuit board.

You are now ready to install the new fan!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 

                    Nicolas Kennedy                     

Member since: 01/26/2014

111 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       Cal Poly, Team 9-30, Maness Winter 2014                        

                                                  Member of Cal Poly, Team 9-30, Maness Winter 2014 



                    CPSU-MANESS-W14S9G30                     


                                            3 Members                     


                                            5 Guides authored                     

darren cottenham - Jun 29, 2020

Reply

We’re can i get a replacement fan for my Blu- ray player model BDV-E4100. HEEEEELP PLEASE.

Christopher Meriweather - Aug 5, 2020

Reply

Where can I get a replacement fan for my blue-ray player.