Difficulty
Easy
Steps
10
Time Required
15 - 20 minutes
Sections
3
- Back Cover
- 4 steps
- Front Panel Cover
- 4 steps
- Front Panel Board
- 2 steps
Flags
0
BackSony BDP-S7200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove the disk tray cover from the device.
Remove the disk tray cover from the device.
1024
Step 2
- Using the Phillips #2 Screwdriver, remove the five 9mm from the bottom of the device.
- Remove the metal cover.
Using the Phillips #2 Screwdriver, remove the five 9mm from the bottom of the device.
Remove the metal cover.
Step 3
- Using the Phillips #2 Screwdriver, remove the six 9mm screws from the back of the device.
Using the Phillips #2 Screwdriver, remove the six 9mm screws from the back of the device.
Step 4
- Pull off the back panel and remove it from the device.
Pull off the back panel and remove it from the device.
Step 5
Front Panel Cover
- Using the plastic opening tool, open one of the tabs on the bottom of the device.
- While keeping the tab open, insert a opening pick in between the opening tool and tab.
- Repeat this for the 3 other tabs.
Using the plastic opening tool, open one of the tabs on the bottom of the device.
While keeping the tab open, insert a opening pick in between the opening tool and tab.
Repeat this for the 3 other tabs.
Step 6
- Place your hands on the two black circles on the bottom of the device.
- Pull on the black circles to remove the device from its front panel cover.
Place your hands on the two black circles on the bottom of the device.
Pull on the black circles to remove the device from its front panel cover.
Step 7
- Using the Phillips #2 Screwdriver, remove the seven 9mm screws from the top of the device.
- Using the same screwdriver, remove the three 9mm screws from the back of the device.
- Using the same screwdriver, remove the one 9mm screw still connecting the small metal clip to the front of the device.
Using the Phillips #2 Screwdriver, remove the seven 9mm screws from the top of the device.
Using the same screwdriver, remove the three 9mm screws from the back of the device.
Using the same screwdriver, remove the one 9mm screw still connecting the small metal clip to the front of the device.
Step 8
- Remove the small metal clip on the front of the device.
- Remove the metal cover on the top of the device.
Remove the small metal clip on the front of the device.
Remove the metal cover on the top of the device.
Step 9
Front Panel Board
- Unplug the large ribbon cable connecting the front panel board to the motherboard.
Unplug the large ribbon cable connecting the front panel board to the motherboard.
Step 10
- Unplug the small ribbon cable connecting the front panel board to the smaller board to the left of it.
- Using the Phillips #2 Screwdriver, remove the one 9mm screw connecting the front panel board to the device.
- Remove the front panel board.
Unplug the small ribbon cable connecting the front panel board to the smaller board to the left of it.
Using the Phillips #2 Screwdriver, remove the one 9mm screw connecting the front panel board to the device.
Remove the front panel board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Lucas Donahue
Member since: 01/16/2020
106 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
Embry-Riddle Aeronautical University, Team S7-G11, Rauch Spring 2020
Member of Embry-Riddle Aeronautical University, Team S7-G11, Rauch Spring 2020
ERAU-RAUCH-S20S7G11
3 Members
4 Guides authored
