Difficulty
Moderate
Steps
12
Time Required
20 - 30 minutes
Sections
3
- Back Cover
- 4 steps
- Front Panel Cover
- 4 steps
- Power Supply Board
- 4 steps
Flags
0
BackSony BDP-S7200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove the disk tray cover from the device.
Remove the disk tray cover from the device.
1024
Step 2
- Using the Phillips #2 Screwdriver, remove the five 9mm from the bottom of the device.
- Remove the metal cover.
Using the Phillips #2 Screwdriver, remove the five 9mm from the bottom of the device.
Remove the metal cover.
Step 3
- Using the Phillips #2 Screwdriver, remove the six 9mm screws from the back of the device.
Using the Phillips #2 Screwdriver, remove the six 9mm screws from the back of the device.
Step 4
- Pull off the back panel and remove it from the device.
Pull off the back panel and remove it from the device.
Step 5
Front Panel Cover
- Using the plastic opening tool, open one of the tabs on the bottom of the device.
- While keeping the tab open, insert a opening pick in between the opening tool and tab.
- Repeat this for the 3 other tabs.
Using the plastic opening tool, open one of the tabs on the bottom of the device.
While keeping the tab open, insert a opening pick in between the opening tool and tab.
Repeat this for the 3 other tabs.
Step 6
- Place your hands on the two black circles on the bottom of the device.
- Pull on the black circles to remove the device from its front panel cover.
Place your hands on the two black circles on the bottom of the device.
Pull on the black circles to remove the device from its front panel cover.
Step 7
- Using the Phillips #2 Screwdriver, remove the seven 9mm screws from the top of the device.
- Using the same screwdriver, remove the three 9mm screws from the back of the device.
- Using the same screwdriver, remove the one 9mm screw still connecting the small metal clip to the front of the device.
Using the Phillips #2 Screwdriver, remove the seven 9mm screws from the top of the device.
Using the same screwdriver, remove the three 9mm screws from the back of the device.
Using the same screwdriver, remove the one 9mm screw still connecting the small metal clip to the front of the device.
Step 8
- Remove the small metal clip on the front of the device.
- Remove the metal cover on the top of the device.
Remove the small metal clip on the front of the device.
Remove the metal cover on the top of the device.
Step 9
Power Supply Board
- Remove the ribbon cables that connect to the front panel board.
- Pull firmly, but not too hard as to not damage the ribbon cable.
Remove the ribbon cables that connect to the front panel board.
Pull firmly, but not too hard as to not damage the ribbon cable.
Step 10
- Remove the power supply board cable connected to the motherboard.
- Pull firmly, but not too hard as to not damage the ribbon cable.
Remove the power supply board cable connected to the motherboard.
Step 11
- Remove the 2 screws using the Phillips #2 screwdriver
- Slide the power cord out of it’s slot in the frame.
Remove the 2 screws using the Phillips #2 screwdriver
Slide the power cord out of it’s slot in the frame.
Step 12
- Remove the Power Supply Board.
Remove the Power Supply Board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Erik Preston
Member since: 01/16/2020
412 Reputation
3 Guides authored
Badges:
7
+4 more badges
Team
Embry-Riddle Aeronautical University, Team S7-G11, Rauch Spring 2020
Member of Embry-Riddle Aeronautical University, Team S7-G11, Rauch Spring 2020
ERAU-RAUCH-S20S7G11
3 Members
4 Guides authored
