Difficulty
Moderate
Steps
13
Time Required
30 minutes
Sections
2
- Disassembling Sony CCD-TR81 Battery
- 3 steps
- Outer Case
- 10 steps
Flags
0
BackSony CCD-TR81
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Disassembling Sony CCD-TR81 Battery
- Lift viewfinder to access battery pack.
Lift viewfinder to access battery pack.
1024
Step 2
- Press the battery release button.
- While pushing the battery button, slide the battery to the left.
Press the battery release button.
While pushing the battery button, slide the battery to the left.
Step 3
- Pull the battery pack out of the video camera.
Pull the battery pack out of the video camera.
Step 4
Outer Case
- Open the cassette cover.
- Unscrew 14 screws located on the outer casing. Three are located on the top face 2x6.8mm and 1X4.54mm, three on the left face 1x4.54mm,1x5.3mm and seven on the bottom face 5x4.54mm and 2x6.77mm.
Open the cassette cover.
Unscrew 14 screws located on the outer casing. Three are located on the top face 2x6.8mm and 1X4.54mm, three on the left face 1x4.54mm,1x5.3mm and seven on the bottom face 5x4.54mm and 2x6.77mm.
Step 5
- Remove five screws from the right side, from bottom to top, 3x4.54mm 2x5.70mm.
- Remove the single 4.5 mm screw from the backside.
Remove five screws from the right side, from bottom to top, 3x4.54mm 2x5.70mm.
Remove the single 4.5 mm screw from the backside.
Step 6
- Pull off the plastic tape cover by lifting it up and out of the camera base.
Pull off the plastic tape cover by lifting it up and out of the camera base.
Step 7
- Disconnect the mic assembly by pulling it away from the camera base.
- Do not pull too hard as the wires are still connected.
Disconnect the mic assembly by pulling it away from the camera base.
Do not pull too hard as the wires are still connected.
Step 8
- Pull the bottom part of the case away from the camera.
Pull the bottom part of the case away from the camera.
Step 9
- Remove the three 4.5 mm screws from the right face of the video camera.
Remove the three 4.5 mm screws from the right face of the video camera.
Step 10
- Remove the single 3.6 mm screw at the front of the video camera on the circuit board.
Remove the single 3.6 mm screw at the front of the video camera on the circuit board.
Step 11
- Pull the audio/video inputs underneath the microphone assembly. The inputs should still be connected to the circuit board.
Pull the audio/video inputs underneath the microphone assembly. The inputs should still be connected to the circuit board.
Step 12
- Remove two remaining 3.6 mm case screws from the front of the camera.
Remove two remaining 3.6 mm case screws from the front of the camera.
Step 13
- Using metal tweezers, pull out the plastic connector box on the front side.
- Again use metal tweezers to pull out the connection box on the bottom of the camera. The right side of the case can now be removed by pulling it to the right.
Using metal tweezers, pull out the plastic connector box on the front side.
Again use metal tweezers to pull out the connection box on the bottom of the camera. The right side of the case can now be removed by pulling it to the right.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 7 other contributors
Kevin
Member since: 01/24/2011
232 Reputation
3 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 11-25, Maness Winter 2011
Member of Cal Poly, Team 11-25, Maness Winter 2011
CPSU-MANESS-W11S11G25
4 Members
5 Guides authored
