Difficulty
Difficult
Steps
8
Time Required
50 minutes - 1 hour
Sections
2
- Main Speaker Housing Disassembly
- 6 steps
- Main Speakers
- 2 steps
Flags
0
BackSony CPF-IP001
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Main Speaker Housing Disassembly
- Remove two 6mm Phillips #0 screws.
- Remove two 7.5 mm Phillips #0 screws.
- Remove seven 4 mm Phillips #0 screws.
Remove two 6mm Phillips #0 screws.
Remove two 7.5 mm Phillips #0 screws.
Remove seven 4 mm Phillips #0 screws.
1024
Step 2
- Remove six 4 mm Phillips #0 screws from the metal backing.
- Remove six 5 mm Phillips #0 screws from the metal backing.
- Using the plastic opening tool, remove the metal plate from the main speaker by gently pulling on it.
Remove six 4 mm Phillips #0 screws from the metal backing.
Remove six 5 mm Phillips #0 screws from the metal backing.
Using the plastic opening tool, remove the metal plate from the main speaker by gently pulling on it.
Step 3
- Remove the plastic dock cover by using two fingers to push the attached metal piece forward and slide it out of the holes.
Remove the plastic dock cover by using two fingers to push the attached metal piece forward and slide it out of the holes.
Step 4
- Using the plastic opening tool, detach the wires connected to the metal plate
- When disconnecting the wires, be careful not to pull on the wires themselves. Use the plastic opening tool and the connector to disconnect it.
- Use the plastic opening tool to remove wires connected to the circuit board on the far right.
- Use the tweezers to remove wires connected to the circuit board in between the two black wires.
- Use the tweezers to press the release tab on the front and back of the plastic white wire head.
- Once the tab is pressed on both sides, lift up to slide wire head out of socket.
Using the plastic opening tool, detach the wires connected to the metal plate
When disconnecting the wires, be careful not to pull on the wires themselves. Use the plastic opening tool and the connector to disconnect it.
Use the plastic opening tool to remove wires connected to the circuit board on the far right.
Use the tweezers to remove wires connected to the circuit board in between the two black wires.
Use the tweezers to press the release tab on the front and back of the plastic white wire head.
Once the tab is pressed on both sides, lift up to slide wire head out of socket.
Step 5
- Remove two 5 mm Phillips #0 screws.
Remove two 5 mm Phillips #0 screws.
Step 6
- Using the metal spudger, loosen the metal cap at the end of the speaker.
- Slide down the loosened cap to remove it from the end of the speaker.
- Simultaneously push down on the buttons and slide the speaker out from the casing.
Using the metal spudger, loosen the metal cap at the end of the speaker.
Slide down the loosened cap to remove it from the end of the speaker.
Simultaneously push down on the buttons and slide the speaker out from the casing.
Step 7
Main Speakers
- Remove eight 5 mm Phillips #0 screws.
Remove eight 5 mm Phillips #0 screws.
Step 8
- Gently pry the speaker out from the housing using the metal spudger.
- Use wire cutters to cut the red and black wires, or desolder the speaker wires to remove the speaker. See iFixit’s guide on How To Solder and Desolder Connections.
Gently pry the speaker out from the housing using the metal spudger.
Use wire cutters to cut the red and black wires, or desolder the speaker wires to remove the speaker. See iFixit’s guide on How To Solder and Desolder Connections.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 3 other contributors
Marlena Perez
Member since: 04/14/2015
430 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 6-14, Maness Spring 2015
Member of Cal Poly, Team 6-14, Maness Spring 2015
CPSU-MANESS-S15S6G14
4 Members
8 Guides authored
