Sony Cpf Ip001 Power Cord Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Subwoofer Housing Disassembly
5 steps
Power Cord
4 steps

Flags

BackSony CPF-IP001
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Subwoofer Housing Disassembly

Remove fourteen 8 mm Phillips #2 screws from the bottom of the subwoofer.
Once all of the screws are removed, the cover can be taken off using a metal spudger.

Remove fourteen 8 mm Phillips #2 screws from the bottom of the subwoofer.

Once all of the screws are removed, the cover can be taken off using a metal spudger.

1024

Step 2

Remove eight 14 mm Phillips #2 screws holding the circuit board in place.
Using the plastic opening tool, carefully remove the circuit board.
There will be 3 wires connected to the opposite side of the circuit board. Be careful not to pull the board out of the device too far and damage these wires.

Remove eight 14 mm Phillips #2 screws holding the circuit board in place.

Using the plastic opening tool, carefully remove the circuit board.

There will be 3 wires connected to the opposite side of the circuit board. Be careful not to pull the board out of the device too far and damage these wires.

Step 3

Remove the first of the three wires by squeezing the clip and pulling it out.
After disconnecting the first wire, the two attached wires can be more easily accessed.

Remove the first of the three wires by squeezing the clip and pulling it out.

After disconnecting the first wire, the two attached wires can be more easily accessed.

Step 4

Remove the wire furthest to the left by squeezing the clip and pulling it out.
Detach the third wire by carefully using the tweezers.
The circuit board is now completely detached and can be set aside.

Remove the wire furthest to the left by squeezing the clip and pulling it out.

Detach the third wire by carefully using the tweezers.

The circuit board is now completely detached and can be set aside.

Step 5

Remove six 8 mm Phillips #2 screws.
Slide the side panel with the power cord out from the housing.
The side panel with the power cord will come out as a whole unit with the subwoofer air tunnel.

Remove six 8 mm Phillips #2 screws.

Slide the side panel with the power cord out from the housing.

The side panel with the power cord will come out as a whole unit with the subwoofer air tunnel.

Step 6

              Power Cord

Remove four 8 mm Phillips #2 screws.
Detach the air tube from the side panel.

Remove four 8 mm Phillips #2 screws.

Detach the air tube from the side panel.

Step 7

Begin to pry the power cord cover unit from the side panel using a metal spudger.
Feed the wires that come out of the side panel through the glue and into the power cord cover unit to get the cover farther away from the side panel.

Begin to pry the power cord cover unit from the side panel using a metal spudger.

Feed the wires that come out of the side panel through the glue and into the power cord cover unit to get the cover farther away from the side panel.

Step 8

Using a metal spudger, disconnect the four spade connectors that are connected to the power button and the power cord.

Using a metal spudger, disconnect the four spade connectors that are connected to the power button and the power cord.

Step 9

Using a metal spudger, press the tab on top of the power cord and push the power cord through the side panel.
Once through, the clip connected to the power cord will open up and a new power cord can be put in place.

Using a metal spudger, press the tab on top of the power cord and push the power cord through the side panel.

Once through, the clip connected to the power cord will open up and a new power cord can be put in place.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Mike Bolton

Member since: 04/14/2015

473 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 6-14, Maness Spring 2015                        

                                                  Member of Cal Poly, Team 6-14, Maness Spring 2015 



                    CPSU-MANESS-S15S6G14                     


                                            4 Members                     


                                            8 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team